1. To understand the Piping material demands of multiple projects & framing the project guidelines as per project requirements 2. Communicate to the project team members related to specifications, project guidelines and deliverable expectations. 3. Develop Piping Material Specification and Valve Material Specifications for piping and pipelines 4. Guide the leads/ team members on material/Specification related information and give appropriate suggestions for improvement 5. Review and monitor design, specifications, MTO, data sheets prepared by the team for conformance to the codes, regulations and project requirements 6. Involve in design, Layout study/developments and Optimization to ensure cost effective solutions. 7. Propose new solutions and evaluate their relative merit. Seek technical guidance on complex and unusual problems from the superior. 8. Involve in Model reviews and comments close out 9. Perform various pipe thickness calculations as per International codes and standards 10. Preparation of technical specification, Bid evaluation, technical recommendations and vendor document review/comments for piping items and piping specialty 11. Conceptual design/ FEED/ Basic and Detail Engineering activities for piping 12. Any other relevant activities as defined by the Manager/Lead."

1. To understand the Piping material demands of multiple projects & framing the project guidelines as per project requirements 2. Communicate to the project team members related to specifications, project guidelines and deliverable expectations. 3. Develop Piping Material Specification and Valve Material Specifications for piping and pipelines 4. Guide the leads/ team members on material/Specification related information and give appropriate suggestions for improvement 5. Review and monitor design, specifications, MTO, data sheets prepared by the team for conformance to the codes, regulations and project requirements 6. Involve in design, Layout study/developments and Optimization to ensure cost effective solutions 7. Propose new solutions and evaluate their relative merit. Seek technical guidance on complex and unusual problems from the superior. 8. Involve in Model reviews and comments close out 9. Perform various pipe thickness calculations as per International codes and standards 10. Preparation of technical specification, Bid evaluation, technical recommendations and vendor document review/comments for piping items and piping specialty 11. Conceptual design/ FEED/ Basic and Detail Engineering activities for piping 12. Engineering coordination and procurement assistance 13. Able to build a friendly climate, good morale and co-operation within teams, provide help to colleagues across disciplines and resolve conflicts within teams. 14. Set priorities, plans and organizes own workload. Systematically monitors the activities & results and interacts with others to ensure on time delivery and in conformance with specifications. 15. Acts as an example for others & embraces changing situations. 16. To involve in the recruitment process as directed by the Manager. 17. To identify training needs based on the project requirements. 18. To interface with other disciplines on material aspects and advice Leads/EPMs during project execution. 19. To keep abreast of relevant developments in material engineering with respect to the offshore/onshore industry. 20. Able to prepare and up-grade project standards and company specifications. 21. To conduct/attend the training courses, seminars etc. when required. 22. Any other relevant activities as defined by the Manager/Lead."

a. Able to read & understand Project specifications, Scope of Work documents, Interpret International rules & regulations b. Familiarity with the Preparation of HT and LT Cable sizing, cable schedule , Single line diagrams and Schematics, Lighting Calculations, Lighting DB schedules, Lighting Loop Diagrams, Interconnection diagrams, MTO\u2019s c. Able to Co-ordinate with designers and provide required inputs for the preparation of various Electrical Layouts d. Able to review the 3D Model in Navis

Familiarity with the Preparation of HT and LT Cable sizing, cable schedule , Single line diagrams and Schematics, Lighting Calculations, Lighting DB schedules, Lighting Loop Diagrams Interconnection diagrams,

1. To perform Stress analysis, Design calculations of various piping system using Caesar-II . 2. Checking of Piping drawings, Isometrics, support drawings. 3. To prepare critical line list as per process/project requirements. 4. Stress analysis of piping system connected to critical equipments such as compressors, pumps and steam turbine to review of piping force & moments. 5. Stress analysis of piping system connected to critical stable equipments to review pipe line. 6. Carrying out all calculations related to displacement of various equipments, branch reinforcement calculation, PSU reaction force calculation, slug force, trunnion calculation, flange leakage test for high temperature lines etc. preparation of piping load data & platform load data. 7. Selection of support as per project requirement (guide, hold down, anchor, spring hanger, struts, clamps etc). 8. Perform stress analysis of pipe rack and produce support load report to structural. 9. Preparation of stress analysis report, support design and mark ups on piping Isometrics 10. Review of vendor drawings and co-ordination with other department. 11. Analysis of systems to ensure stress, loads and displacement are within the limit as per project requirement, recommendations for modification. 12. Creativity and presenting stress reports as per the client requirement. 13. To coordinate with piping and other disciplines and ensure that they get the necessary inputs on time. 14. Any other relevant activities as defined by the Manager/Lead."

1.Able to perform routine calculation. 2.Seeks guidance on Non-routine tasks 3.Solves simple straight forward problems with in own working area. 4.Makes suggestions to Designs. 5.Delivers inputs to concept selection 6.Has a perspective of work involvement for the coming months 7.Gives input to Supervisor for solving recurring problems. 8.Works on Projects. Assigns work to juniors. 9.Able to operate in dynamic changing environment. 10.Any other relevant activities defined by Lead/Manager.

1. Getting task from supervisor and to complete it within the schedule. 2.To study the P&ID\u2019s, project documents and standards as per requirements. 3.Routing of pipes and modifications during non-checking time. 4.Checking of all piping documents like Isometrics, piping plans, plot plans, pipe supports etc. prepared by the Designers. 5.Checking of VPE P&IDs for PID projects. 6.To issue all the deliverables through Leads. 7.To guide/clarify juniors on routing and any other necessary support required. 8.To ensure quality delivery on time by meeting the required specification. 9.Master P&ID marking and updating/monitoring change log sheets. 10.To identify any unusual or specific features which affect the safe and efficient installation, operation and maintenance of piping systems and equipments. 11.To follow all relevant project guidelines and departmental work instructions in the design and drawing of equipments and piping systems. 12.To attend training courses, seminars, internal meetings etc. when required. 13.Maintain proper documentation during project life cycle. 14.Any other relevant activities as defined by the Manager/Lead.

1.Able to perform calculations of normal complexity. 2.Seeks guidance for complex tasks 3.Works on projects or in proposal development. 4.Instruct and teaches less experienced colleagues. 5.Analysis & Design of Structural systems using software in compliance with client requirements and preparation of respective documents. 6.Finalizing the structural system and get the approval from Structural Lead before issuing. 7.Structural system is prepared keeping in view transfer of loads to primary system effectively. 8.Writes specifications and selection of standard equipment or components under guidance of Leads. 9.Is able to analyze alternatives and identifies best technical solution. Provides input to concept developments. 10.Makes suggestions to improve calculations, process and Designs. 11.Able to operate in a dynamic, changing environment. 12.Has a perspective of work involvement for the coming months. 13.Be able to see cost impact, Schedule impact, constructability and maintainability of Designs. 14.Responsible for technical procurement, Follow-up of standard equipment or components for Projects. 15.Assigned as Lead on small projects for his/her own discipline. 16.Any other relevant activities defined by Lead/Manager.

Develop and optimize process designs for various systems, ensuring they meet required specifications and safety standards. Prepare and manage data sheets for process equipment such as control valves, heat exchangers, and pumps. Utilize software such as Aspen and HYSYS to model and analyze process systems. Work on process flow diagrams (PFDs) and piping & instrumentation diagrams (P&IDs). Perform hydraulic calculations and design specifications for control valves, heat exchangers, and other process equipment. Support process design in oil & gas, wastewater treatment, and production engineering projects. Solve complex process-related issues by applying sound engineering principles and practices. Collaborate with other engineering disciplines, providing technical support as needed. Requirements Qualifications : Bachelors degree in Chemical Engineering, Process Engineering, or related field. Strong experience with Aspen , HYSYS , and other process simulation software. Experience in designing and optimizing process systems in the Oil & Gas industry. Proficiency with Microsoft Visio , Navisworks , and other design and documentation tools. Solid understanding of control valves , heat exchangers , data sheet preparation , and wastewater treatment .

1. Should go through the scope of work, Project documentation, Standards & guide lines before commencement of work 2. Preparation of LOD (List of Deliverables) after discussing with Project Manager/Project coordinator. 3. Assigning tasks to each team member. 4. Reviewing the project on a regular basis. 5. To ensure that the Safety Management System and Quality Assurance requirements are followed throughout the engineering phase. 6. The ability to listen, respond, interact, and communicate successfully and appropriately with the team. 7. The ability to address conflict/challenges related to Piping design and resolve them. 8. Improvises and improves processes to meet requirements. 9. To study the P&IDs and give inputs to designers on pipe routing and modifications (if Engineer/Design engineers are not available) 10. Checking of deliverables like Isometrics, GADs, Bill of Materials etc executed by the designers. (If Engineer/checker is not available) 11. Final reviewing of documents received by checkers 12. Development of conceptual equipment layouts and piping layouts. 13. Any other relevant activities as defined by the Manager/lead

1. To perform Stress analysis, Design calculations of various piping system using Caesar-II. 2. Checking of Piping drawings, Isometrics, support drawings. 3. Stress analysis of piping system connected to critical equipments such as compressors, pumps and steam turbine to review of piping force & moments. 4. Stress analysis of piping system connected to critical stable equipments to review pipe line. 5. Carrying out all calculation related displacement of various equipments, branch reinforcement calculation, PSU reaction force calculation, slug force, trunnion calculation, flange leakage test for high temperature lines etc. preparation of piping load data, platform load data & BU load. Data. 6. Selection of support as per project requirement ( guide, holddown, anchor, spring hanger, struts, clamps etc) 7. Preparation of spring support & spring hanger data sheet. Preparation and issue of piping loads to civil and structural and co-ordinate with Structural for design of supports. 8. Perform stress analysis of pipe rack and produce support load report to structural. 9. Dealing site queries with producing relevant information with clients. 10. Preparation of stress analysis report, support design and mark ups on piping drawings. 11. Review of vendor drawings and co-ordination with other department. 12. Analysis the system to ensure stress, loads and displacement are within the limit as per project requirement, recommendations for modification. 13. Creativity and presenting stress reports as per the client requirement. 14. To coordinate with piping and other disciplines and ensure that they get the necessary inputs on time. 15. Any other relevant activities as defined by the Manager/Lead."

1. To understand the Piping material demands of multiple projects & framing the project guidelines as per project requirements 2. Communicate to the project team members related to specifications, project guidelines and deliverable expectations. 3. Develop Piping Material Specification and Valve Material Specifications for piping and pipelines 4. Guide the leads/ team members on material/Specification related information and give appropriate suggestions for improvement 5. Review and monitor design, specifications, MTO, data sheets prepared by the team for conformance to the codes, regulations and project requirements 6. Involve in design, Layout study/developments and Optimization to ensure cost effective solutions 7. Propose new solutions and evaluate their relative merit. Seek technical guidance on complex and unusual problems from the superior. 8. Involve in Model reviews and comments close out 9. Perform various pipe thickness calculations as per International codes and standards 10. Preparation of technical specification, Bid evaluation, technical recommendations and vendor document review/comments for piping items and piping specialty 11. Conceptual design/ FEED/ Basic and Detail Engineering activities for piping 12. Engineering coordination and procurement assistance 13. Able to build a friendly climate, good morale and co-operation within teams, provide help to colleagues across disciplines and resolve conflicts within teams. 14. Set priorities, plans and organizes own workload. Systematically monitors the activities & results and interacts with others to ensure on time delivery and in conformance with specifications. 15. Acts as an example for others & embraces changing situations. 16. To involve in the recruitment process as directed by the Manager. 17. To identify training needs based on the project requirements. 18. To interface with other disciplines on material aspects and advice Leads/EPMs during project execution. 19. To keep abreast of relevant developments in material engineering with respect to the offshore/onshore industry. 20. Able to prepare and up-grade project standards and company specifications. 21. To conduct/attend the training courses, seminars etc. when required. 22. Any other relevant activities as defined by the Manager/Lead.

- Understanding the Project Guidelines and Standards - Able deliver the task assigned by leads - Should understand the project schedule / mile stone and adhere to it - Review the documents & drawings generated by peers - Should be familiar with P&ID, Instrument Index etc - Should be capable of preparing & reviewing of construction documents like Cable tray layouts, JB layouts, hook-up etc. - Coordinates with other internal/external team members on the design related issues

1. To perform Stress analysis, Design calculations of various piping system using Caesar-II. 2. Checking of Piping drawings, Isometrics, support drawings. 3. To prepare critical line list as per process/project requirements. 4. Stress analysis of piping system connected to critical equipments such as compressors, pumps and steam turbine to review of piping force & moments. 5. Stress analysis of piping system connected to critical stable equipments to review pipe line. 6. Carrying out all calculations related to displacement of various equipments, branch reinforcement calculation, PSU reaction force calculation, slug force, trunnion calculation, flange leakage test for high temperature lines etc. preparation of piping load data & platform load data. 7. Selection of support as per project requirement (guide, hold down, anchor, spring hanger, struts, clamps etc) 8. Perform stress analysis of pipe rack and produce support load report to structural. 9. Preparation of stress analysis report, support design and mark ups on piping Isometrics 10. Review of vendor drawings and co-ordination with other department. 11. Analysis of systems to ensure stress, loads and displacement are within the limit as per project requirement, recommendations for modification. 12. Creativity and presenting stress reports as per the client requirement. 13. To coordinate with piping and other disciplines and ensure that they get the necessary inputs on time. 14. Any other relevant activities as defined by the Manager/Lead."

1. Getting task from supervisor and to complete it within the schedule. 2.To study the P&ID\u2019s, project documents and standards as per requirements. 3.Routing of pipes and modifications during non-checking time. 4.Checking of all piping documents like Isometrics, piping plans, plot plans, pipe supports etc. prepared by the Designers. 5.Checking of VPE P&IDs for PID projects. 6.To issue all the deliverables through Leads. 7.To guide/clarify juniors on routing and any other necessary support required. 8.To ensure quality delivery on time by meeting the required specification. 9.Master P&ID marking and updating/monitoring change log sheets. 10.To identify any unusual or specific features which affect the safe and efficient installation, operation and maintenance of piping systems and equipments. 11.Maintain proper documentation during project life cycle. 12.Any other relevant activities as defined by the Manager/Lead.

1. Should go through the scope of work, Project documentation, Standards & guide lines before commencement of work. 2. Preparation of LOD (List of Deliverables) after discussing with Project Manager/Project coordinator. 3. Assigning tasks to each team member. 4. Reviewing the project on a regular basis. 5. To ensure that the Safety Management System and Quality Assurance requirements are followed throughout the engineering phase. 6. The ability to listen, respond, interact, and communicate successfully and appropriately with the team. 7. The ability to address conflict/challenges related to Piping design and resolve them. 8. Improvises and improves processes to meet requirements. 9. To guide/clarify juniors & checkers on routing, project related queries and any other necessary support required 10. To provide the timely information to the team members to complete the project 11. Mentors others key skills and processes and shares best practices. 12. To study the P&IDs and give inputs to designers on pipe routing and modifications (if Engineer/Design engineers are not available) 13. Checking of deliverables like Isometrics, GADs, Bill of Materials etc executed by the designers. (If Engineer/checker is not available) 14. Final reviewing of documents received by checkers 15. To represent the department and/or Company in internal Company meetings or wherever elsewhere worldwide, with client, subcontractors, suppliers etc. 16. To conduct regular team meetings to monitor the progress of the project & suggest or plan with the help of department manager to meet the project deadline. 17. To plan & suggest for the training activities as & when required. 18. Development of conceptual equipment layouts and piping layouts. 19. Maintain proper documentation during project life cycle. Any other relevant activities as defined by the Manager/lead"

- Understanding the scope of work, Project documentation, Standards & Guidelines . - Able deliver the task assigned by leads within schedule. - Should be familiar with P&ID, Instrument Index etc. - Should be capable of preparing documents like Cable tray layouts, JB layouts, interconnection diagram, hook-up, MTO etc.

1 Should go through the scope of work, Project documentation, Standards & guide lines before commencement of work. 2. Preparation of LOD (List of Deliverables) after discussing with Project Manager/Project coordinator. 3. Assigning tasks to each team member. 4. Reviewing the project on a regular basis. 5. To ensure that the Safety Management System and Quality Assurance requirements are followed throughout the engineering phase. 6. The ability to listen, respond, interact, and communicate successfully and appropriately with the team. 7. The ability to address conflict/challenges related to Piping design and resolve them. 8. Improvises and improves processes to meet requirements. 9. To guide/clarify juniors & checkers on routing, project related queries and any other necessary support required 10. To provide the timely information to the team members to complete the project 11. Mentors others key skills and processes and shares best practices. 12. To study the P&IDs and give inputs to designers on pipe routing and modifications (if Engineer/Design engineers are not available) 13. Checking of deliverables like Isometrics, GADs, Bill of Materials etc executed by the designers. (If Engineer/checker is not available) 14. Final reviewing of documents received by checkers 15. To represent the department and/or Company in internal Company meetings or wherever elsewhere worldwide, with client, subcontractors, suppliers etc. 16. To conduct regular team meetings to monitor the progress of the project & suggest or plan with the help of department manager to meet the project deadline. 17. To plan & suggest for the training activities as & when required. 18. Development of conceptual equipment layouts and piping layouts. 19. Maintain proper documentation during project life cycle.

BE (MECH/PROCESS Preferably) Other disciplines also acceptable if Candidate is having multi-disciplinary know-how and hands on experience. 15 to 20 Years Relevant Experience in Planning, Controls & Reporting Activities. Has Previously worked as Planning & Controls Engineer with Primavera P6 experience. Capable of independently developing Planning Package (Project Schedule, PMS etc). Capable of Handling Multiple Projects simultaneously. Good Communication and presentation skills. Experience in Project Risk Management Workshop/Reporting desired