455 Rtl Jobs - Page 2

Job Area: Engineering Group, Engineering Group > Hardware Engineering General Summary: As a leading technology innovator, Qualcomm pushes the boundaries of what's possible to enable next-generation experiences and drives digital transformation to help create a smarter, connected future for all. As a Qualcomm Hardware Engineer, you will plan, design, optimize, verify, and test electronic systems, bring-up yield, circuits, mechanical systems, Digital/Analog/RF/optical systems, equipment and packaging, test systems, FPGA, and/or DSP systems that launch cutting-edge, world class products. Qualcomm Hardware Engineers collaborate with cross-functional teams to develop solutions and meet performance requirements. SOC level Mixed Signal and High Speed Interfaces verification Engineer Experience of 1 year to 6 years in Design Verification Responsible for RTL and GLS level validation at SOC. Post Silicon validation support Familiarity with basic concepts of SV, UVM and C-based test case bringup. Understanding of GLS simulations and debug is a plus. Good in communication. Minimum Qualifications: Bachelor's degree in Computer Science, Electrical/Electronics Engineering, Engineering, or related field and 2+ years of Hardware Engineering or related work experience. OR Master's degree in Computer Science, Electrical/Electronics Engineering, Engineering, or related field and 1+ year of Hardware Engineering or related work experience. OR PhD in Computer Science, Electrical/Electronics Engineering, Engineering, or related field.

Job Area: Engineering Group, Engineering Group > Hardware Engineering General Summary: Experience 3+ years of experience in RTL,UPF & Physical aware Synthesis for cutting edge technology nodes, logic equivalence checking, Scripting and Netlist Timing Signoff Proficiency in Python/Tcl * Familiar with Synthesis tools (Fusion Compiler/Genus), * Fair knowledge in LEC, LP signoff tools * Proficient in VLSI front end design steps- Verilog/VHDL, Synthesis, QoR optimization & Equivalence Checking * Familiarity with standard software engineering practices like Version Control, Configuration Management, Regression is a plus * Should be sincere, dedicated and willing to take up new challenges Minimum Qualifications: Bachelor's degree in Computer Science, Electrical/Electronics Engineering, Engineering, or related field and 4+ years of Hardware Engineering or related work experience. OR Master's degree in Computer Science, Electrical/Electronics Engineering, Engineering, or related field and 3+ years of Hardware Engineering or related work experience. OR PhD in Computer Science, Electrical/Electronics Engineering, Engineering, or related field and 2+ years of Hardware Engineering or related work experience.

Job Area: Engineering Group, Engineering Group > Hardware Engineering General Summary: Qualcomm Chennai is looking for a STA and Synthesis Engineer who is passionate in to work with cross-functional engineering teams. In this position, the engineer will be involved in all stages of the design and development cycles Synthesis, Static Timing Analysis and LEC of SoC/Cores Full chip and block level timing closure, IO budgeting for blocks Logical equivalence check between RTL to Netlist and Netlist to Netlist Knowledge of low-power techniques including clock gating, power gating and MV designs ECO timing flow Proficient in scripting languages (TCL and Perl). Minimum Qualifications: Bachelor's degree in Computer Science, Electrical/Electronics Engineering, Engineering, or related field and 2+ years of Hardware Engineering or related work experience. OR Master's degree in Computer Science, Electrical/Electronics Engineering, Engineering, or related field and 1+ year of Hardware Engineering or related work experience. OR PhD in Computer Science, Electrical/Electronics Engineering, Engineering, or related field. Bachelors / Masters degree in electrical or electronics engineering with 3-6 yrs of experience is preferred

Job Area: Engineering Group, Engineering Group > Hardware Engineering General Summary: As a leading technology innovator, Qualcomm pushes the boundaries of what's possible to enable next-generation experiences and drives digital transformation to help create a smarter, connected future for all. As a Qualcomm Hardware Engineer, you will plan, design, optimize, verify, and test electronic systems, bring-up yield, circuits, mechanical systems, Digital/Analog/RF/optical systems, equipment and packaging, test systems, FPGA, and/or DSP systems that launch cutting-edge, world class products. Qualcomm Hardware Engineers collaborate with cross-functional teams to develop solutions and meet performance requirements. Minimum Qualifications: Bachelor's degree in Computer Science, Electrical/Electronics Engineering, Engineering, or related field and 2+ years of Hardware Engineering or related work experience. OR Master's degree in Computer Science, Electrical/Electronics Engineering, Engineering, or related field and 1+ year of Hardware Engineering or related work experience. OR PhD in Computer Science, Electrical/Electronics Engineering, Engineering, or related field. Minimum of 3+ years experience in the area of DFT-, ATPG, Scan Insertion, MBIST, JTAG -In depth knowledge of DFT concepts. -In depth knowledge and hands on experience in DFT(scan/mbist) insertion, ATPG pattern generation/verification, mbist verification and post silicon bring up/yield analysis -Expertise in test mode timing constraints definition, knowledge in providing timing fixes/corrective actions for timing violations. -Ability to analyze and devise new tests for new technologies/custom RAM design/RMA etc. -Expertise in scripting languages such as perl, shell, etc. -Experience in simulating test vectors. -Knowledge of equivalence check and RTL lint tool (like spyglass). -Ability to work in an international team, dynamic environment -Ability to learn and adapt to new tools and methodologies. -Ability to do multi-tasking & work on several high priority designs in parallel. -Excellent problem-solving skills

Job Area: Engineering Group, Engineering Group > Hardware Engineering General Summary: 5 to 8 years of experience in RTL verification. Develop deep understanding of 3-D Graphics hardware pipeline, feature sets, data paths, block functionalities & interfaces Strategize, brainstorm, and propose a DV environment, develop test bench, own test plan, debug all RTL artefacts, and achieve all signoff matrices Collaborate with worldwide architecture, design, and systems teams to achieve all project goals Currently, we are looking for candidates who can match one or more of the profiles listed below, Strong knowledge in developing UVM based System Verilog TBs and assertion/coverage driven verification methodologies Inclination towards the Core level verification and experience in GPU/CPU/any core level verification is a plus Knowledge about the GPU pipeline is a plus, not mandatory Proficiency with formal tools- working knowledge of Property based FV is a plus, not mandatory Perl/Python scripts for automation in managing regressions, optimize run time, manage database and bug Strong communication skills (both written and verbal) Most importantly, ability to learn, improve and deliver Minimum Qualifications: Bachelor's degree in Computer Science, Electrical/Electronics Engineering, Engineering, or related field and 4+ years of Hardware Engineering or related work experience. OR Master's degree in Computer Science, Electrical/Electronics Engineering, Engineering, or related field and 3+ years of Hardware Engineering or related work experience. OR PhD in Computer Science, Electrical/Electronics Engineering, Engineering, or related field and 2+ years of Hardware Engineering or related work experience.

Job Area: Engineering Group, Engineering Group > Hardware Engineering General Summary: Experience in Logic design /micro-architecture / RTL coding is a must. Must have hands on experience with SoC design and integration for complex SoCs. Experience in Verilog/System-Verilog is a must. Should have knowledge of AMBA protocols - AXI, AHB, APB, SoC clocking/reset/debug architecture and peripherals like USB, PCIE and SDCC. Understanding of Memory controller designs and microprocessors is an added advantage Hands on experience in constraint development and timing closure Work closely with the SoC verification and validation teams for pre/post Silicon debug Hands on experience in Low power SoC design is required Experience in Synthesis / Understanding of timing concepts for ASIC is required. Hands on experience in Multi Clock designs, Asynchronous interface is a must. Experience creating pad ring and working with the chip level floorplan team is an added advantage Experience in using the tools in ASIC development such as Lint, CDC, Design compiler and Primetime is required . Minimum Qualifications: Bachelor's degree in Computer Science, Electrical/Electronics Engineering, Engineering, or related field and 3+ years of Hardware Engineering or related work experience. OR Master's degree in Computer Science, Electrical/Electronics Engineering, Engineering, or related field and 2+ years of Hardware Engineering or related work experience. OR PhD in Computer Science, Electrical/Electronics Engineering, Engineering, or related field and 1+ year of Hardware Engineering or related work experience. Preferred Qualifications 2-9 years of experience in SoC design Educational 2+ years of experience with a Bachelors/ Masters degree in Electrical engineering

Job Area: Engineering Group, Engineering Group > Hardware Engineering General Summary: As a leading technology innovator, Qualcomm pushes the boundaries of what's possible to enable next-generation experiences and drives digital transformation to help create a smarter, connected future for all. As a Qualcomm Hardware Engineer, you will plan, design, optimize, verify, and test electronic systems, bring-up yield, circuits, mechanical systems, Digital/Analog/RF/optical systems, equipment and packaging, test systems, FPGA, and/or DSP systems that launch cutting-edge, world class products. Qualcomm Hardware Engineers collaborate with cross-functional teams to develop solutions and meet performance requirements. Minimum Qualifications: Bachelor's degree in Computer Science, Electrical/Electronics Engineering, Engineering, or related field and 6+ years of Hardware Engineering or related work experience. OR Master's degree in Computer Science, Electrical/Electronics Engineering, Engineering, or related field and 5+ years of Hardware Engineering or related work experience. OR PhD in Computer Science, Electrical/Electronics Engineering, Engineering, or related field and 4+ years of Hardware Engineering or related work experience. As a CPU Physical Design Methodology Engineer, you will work with implementation and CAD teams to implement the designs meeting aggressive power, area and performance goals using industry standard tools/flows for next generation CPUs. : Bachelor's/Masters degree in Electrical Engineering with 5+ years of practical experience Experience with Synthesis, place and route and signoff timing/power analysis. Knowledge of high performance and low power implementation techniques Proficiency in scripting (TCL, Python, Perl) Preferred qualifications Experience in deep submicron process technology nodes is strongly preferred. Knowledge of library cells and optimizations. Solid understanding industry standard tools for synthesis, place & route and tapeout flows. Good data analytical skills to identify and root cause physical design issues. Roles and Responsibilities Work with cross functional teams (RTL, Physical design, Circuits, CAD) to solve key physical design problems in CPU implementations. Develop innovative techniques in Physical design and optimization space to help meet aggressive PPA targets. Work with all external CAD tool vendors and internal CAD teams to identify and improve optimization issues related to CPU designs. Work with all block level implementation teams to analyze, implement and improve the optimization method as it pertains to the designs.

Job Area: Engineering Group, Engineering Group > Hardware Engineering General Summary: As a leading technology innovator, Qualcomm pushes the boundaries of what's possible to enable next-generation experiences and drives digital transformation to help create a smarter, connected future for all. As a Qualcomm Hardware Engineer, you will plan, design, optimize, verify, and test electronic systems, bring-up yield, circuits, mechanical systems, Digital/Analog/RF/optical systems, equipment and packaging, test systems, FPGA, and/or DSP systems that launch cutting-edge, world class products. Qualcomm Hardware Engineers collaborate with cross-functional teams to develop solutions and meet performance requirements. Minimum Qualifications: Bachelor's degree in Computer Science, Electrical/Electronics Engineering, Engineering, or related field and 2+ years of Hardware Engineering or related work experience. OR Master's degree in Computer Science, Electrical/Electronics Engineering, Engineering, or related field and 1+ year of Hardware Engineering or related work experience. OR PhD in Computer Science, Electrical/Electronics Engineering, Engineering, or related field. 3+ Years of Experience in Logic design /micro-architecture / RTL coding Must have hands on experience with SoC design, synthesis and timing analysis for complex SoCs. Experience in Verilog/System-Verilog is a must. knowledge of AMBA protocols - AXI, AHB, APB, SoC clocking/reset/debug architecture and peripherals like USB, PCIE and SDCC. Work closely with the SoC DFT, Physical Design and STA teams Hands on experience in Low power SoC design is required Hands on experience in Multi Clock designs, Asynchronous interface is a must. Experience in using the tools in ASIC development such as DesignCompiler, Genus, FusionCompiler and Primetime is required. Understanding of constraint development and timing closure is a plus. Experience in Synthesis / Understanding of timing concepts

Job Area: Engineering Group, Engineering Group > Hardware Engineering General Summary: Qualcomm WLAN HW team in Bangalore is responsible for developing and delivering best in class WLAN/WiFi solutions which are setting benchmark in wireless industry. In this role of WLAN Verification Engineer, you will be verifying the PHY Sub-System from both TX and RX perspective. The responsibilities will majorly include : Understanding of WLAN PHY TX and RX design paths, Algorithms that control the various aspects of wireless systems Develop test plan to verify WiFi Standards including 11BE, sequences and design components. Own end to end DV tasks from coding Test bench and test cases, write assertions, running simulations and achieving all coverage goals Explore innovative DV methodologies (formal, simulation and emulation based) to continuously push the quality and efficiency of test benches Successful candidate will be required to collaborate with worldwide design, silicon, and architecture teams to achieve all project goals. Hence, we are looking for candidates with strong communication skills. 8+ years industry experience with below skillset : Strong System Verilog/UVM based verification skills & experience with assertion & coverage-based verification methodology Experience in formal / static verification methodologies will be a plus Good understanding of WiFi Standards is a plus Experience with GLS, and scripting languages such as Perl, Python is a plus Education BE/BTech/ME/MTech/MS Communication Engineering and/or Electronics, VLSI from reputed university preferably with distinction Minimum Qualifications: Bachelor's degree in Computer Science, Electrical/Electronics Engineering, Engineering, or related field and 4+ years of Hardware Engineering or related work experience. OR Master's degree in Computer Science, Electrical/Electronics Engineering, Engineering, or related field and 3+ years of Hardware Engineering or related work experience. OR PhD in Computer Science, Electrical/Electronics Engineering, Engineering, or related field and 2+ years of Hardware Engineering or related work experience.

Job Area: Engineering Group, Engineering Group > Hardware Engineering General Summary: As a leading technology innovator, Qualcomm pushes the boundaries of what's possible to enable next-generation experiences and drives digital transformation to help create a smarter, connected future for all. As a Qualcomm Hardware Engineer, you will plan, design, optimize, verify, and test electronic systems, bring-up yield, circuits, mechanical systems, Digital/Analog/RF/optical systems, equipment and packaging, test systems, FPGA, and/or DSP systems that launch cutting-edge, world class products. Qualcomm Hardware Engineers collaborate with cross-functional teams to develop solutions and meet performance requirements. Minimum Qualifications: Bachelor's degree in Computer Science, Electrical/Electronics Engineering, Engineering, or related field and 3+ years of Hardware Engineering or related work experience. OR Master's degree in Computer Science, Electrical/Electronics Engineering, Engineering, or related field and 2+ years of Hardware Engineering or related work experience. OR PhD in Computer Science, Electrical/Electronics Engineering, Engineering, or related field and 1+ year of Hardware Engineering or related work experience. Additional Qualcomm Global CAD Organization is looking for DFT/ATPG Methodology development lead to develop DFTCAD methodologies for Qualcomms 5G products in advanced FinFET semiconductor process nodes. In this role, you will be a member of a global technical team working with SOC Design, DFT, Product and Test, and Diagnostics teams, as well as EDA Tool vendors to develop world-class DFT methodology solutions. Key Responsibilities Lead DFT ATPG flow development, integration, and deployment efforts independently, collaborating with DFT teams, EDA vendors Drive new ATPG methodology, new tool evaluation, design DoEs, both within Qualcomm and partnering with EDA vendors. Develop optimized recipes for improving test quality, reducing test cost, DFT cycle time, pattern simulation runtimes. Qualifications/Experience BE/B.Tech, ME/MTech/MS in Electrical/Electronics/Computer science Engineering 4-6 years demonstrated experience in VLSI EDA/CAD methodology development in areas of DFT, Scan/ATPG Skills Required Strong knowledge of DFT domain specifically on Scan, ATPG and ATPG pattern simulations Strong development skills in TCL, Python Good understanding of SOC DFT Flow, ATE Flow and practices. Familiarity with standard software development process, systems including Configuration Management, QA, Release and Support Ability to plan and execute formal projects, deliverables. Ability to work with multiple WW teams in a fast paced and dynamic environment. Must be a team player, ability to multi-task, with attention to details. Keywords : DFT, ATPG, Scan, VLSI Test, Tessent, TetraMAX, TestMAX, MBIST, SMS

Job Area: Engineering Group, Engineering Group > Hardware Engineering General Summary: Qualcomm is a company of inventors that unlocked 5G ushering in an age of rapid acceleration in connectivity and new possibilities that will transform industries, create jobs, and enrich lives. But this is just the beginning. It takes inventive minds with diverse skills, backgrounds, and cultures to transform 5Gs potential into world-changing technologies and products. This is the Invention Age and this is where you come in. Join QCOM Technologies Inc Global Emulation(Prototyping) team delivering solutions for design of leading-edge wireless products. Qualcomm is leading 5G innovations ushering in an age of rapid acceleration in connectivity and new possibilities that will transform industries, create jobs, and enrich lives. The Qualcomm Global emulation team is currently seeking a lead engineer role for our team doing development/validation of large scale FPGA emulation tools/flows/methodologies In this role, you will be working in multiple areas of SoC/IP prototyping flows and methodologies. Would also involve enabling execution teams doing SOC prototyping during their usage of the platform Minimum Qualifications: Bachelor's degree in Computer Science, Electrical/Electronics Engineering, Engineering, or related field and 2+ years of Hardware Engineering or related work experience. OR Master's degree in Computer Science, Electrical/Electronics Engineering, Engineering, or related field and 1+ year of Hardware Engineering or related work experience. OR PhD in Computer Science, Electrical/Electronics Engineering, Engineering, or related field. 4-7 years of experience working in FPGA Synthesis, Prototyping of SoCs & IPs Candidates are expected to have experience in: Prior work experience on Emulation/Prototyping Platforms (HAPS, VPS, Protium etc) Multi-FPGA prototyping flow, from RTL preparation to h/w implementation Proficient in analysis & debug of issue in Synthesis, Place and Route, Timing closure, Clocking. Hands on experience in FPGA h/w debug using probes/ILA Proficient in EDA tools like - Vivado, Synplify, Protocompiler, VPS, VCS/Verdi etc RTL coding and simulation Well versed with working in unix/linux environment, using GVIM/VI editors, shell scripting Strong debug skills, aptitude to learn and resolve complex issues Experience in one or more scripting language - TCL, Python, Perl, Shell etc Sound knowledge of: FPGA architecture preferably Xilinx (ultrascale), Vivado IP catalog Synthesis, Timing concepts and SDC constraints Prototyping concepts like - partitioning, pinmux

Job Area: Engineering Group, Engineering Group > Hardware Engineering General Summary: Required Qualifications Bachelor's degree /masters degree in Electronics & Tele Engineering, Microelectronics, Computer Science, or related field. 4+ years RTL Design/Hardware Engineering experience or related work experience. Skills/Experience Required Strong Domain Knowledge on RTL Design , implementation, and integration. Experience with RTL coding using Verilog/VHDL/System Verilog. Experience in micro-architecture & designing cores and ASICs. Familiar with the Synthesis, Formal Verification, Linting, CDC, Low Power, UPFs, etc. Exposure in scripting (Pearl/Python/TCL). Strong debugging capabilities at simulation, emulation, and Silicon environments. Collaborate closely with cross-function team located in different time zone to research, design and implement performance and power management strategy for product roadmap. Good team player. Need to interact with the other teams/verification engineers proactively. Responsibilities Design and lead all Front-end design activities for Display Sub-system that deliver cutting edge solution for various Qualcomm business unit like VR, AR, Compute, IOT, Mobile. Perform RTL design, simulation, synthesis, timing analysis, lint check, clock domain crossing check, conformal low power check, and formal verification for IP blocks. Work closely with technology/circuit design team to close IP block specification/requirement. Work closely with verification/physical design team to complete the IP design implementation. Support SoC team to integrate Display Sub-system IP solution into various SoC chips and front-end design flows. Work closely with system/software/test team to enable the low power feature in wireless SoC product. Evaluate new low-power technologies and analyze their applications to address requirements. Understand and perform block & chip-level performance analysis & identify performance bottleneck and provide required solution. Minimum Qualifications: Bachelor's degree in Computer Science, Electrical/Electronics Engineering, Engineering, or related field and 3+ years of Hardware Engineering or related work experience. OR Master's degree in Computer Science, Electrical/Electronics Engineering, Engineering, or related field and 2+ years of Hardware Engineering or related work experience. OR PhD in Computer Science, Electrical/Electronics Engineering, Engineering, or related field and 1+ year of Hardware Engineering or related work experience.

Job Area: Engineering Group, Engineering Group > Hardware Engineering General Summary: Minimum 4 to 8 years of work experience in ASIC RTL Design, Synthesis, STA & FVExperience in Logic design/micro-architecture/RTL coding is a must.Must have hands on experience with design and integration of complex multi clock domain blocksExperience in Verilog/System-Verilog is a must.Should have knowledge of AMBA protocols - AXI, AHB, APB, clocking/reset/debug architectureHands on experience in Multi Clock designs, Asynchronous interface is a must.Experience in using the tools in ASIC development such as Lint, CDC, Design compiler and Primetime is required.Work closely with the Design verification and validation teams for pre/post Silicon debugHands on experience in Low power design is preferableExperience in Synthesis / Understanding of timing concepts for ASIC is must Minimum Qualifications: Bachelor's degree in Computer Science, Electrical/Electronics Engineering, Engineering, or related field and 3+ years of Hardware Engineering or related work experience. OR Master's degree in Computer Science, Electrical/Electronics Engineering, Engineering, or related field and 2+ years of Hardware Engineering or related work experience. OR PhD in Computer Science, Electrical/Electronics Engineering, Engineering, or related field and 1+ year of Hardware Engineering or related work experience.

Job Area: Engineering Group, Engineering Group > Hardware Engineering General Summary: QCT's Bangalore Wireless R&D HW team is looking out for experienced Wireless Modem HW model developers to work on Qualcomms best in class chipsets in modem WWAN IPs Roles and Responsibilities You will be contributing to flagship modem core IP development covering 5G(NR) & 4G (LTE) technologies. You will be part of team defining and developing next generation multi-mode 5G modems. You will be working on development and verification of HW models of modem core IP. The models are developed on C++/SystemC platform and used as golden reference for RTL verification and pre Silicon FW development ( virtual prototyping). The candidate must be well versed with C++ and should have good exposure to SystemC and/or System Verilog and/or Matlab. The candidate must have ability to understand HW micro-architecture & its modeling abstraction. Working knowledge of physical layer of wireless technologies like NR,LTE , WLAN, Bluetooth is highly desired. Expertise on digital signal processing and working experience on HW modeling and/or RTL design/ verification of IP are preferred. Candidates with SW/FW background on wireless IP can also apply. Candidates with strong technical knowhow on non-wireless DSP based HW IPs ( with Design / Verification/ Modeling skills) will also be considered. Minimum qualification Bachelors or Masters in Electrical/Electronics/Computers Science from reputed college/university. Minimum Qualifications: Bachelor's degree in Computer Science, Electrical/Electronics Engineering, Engineering, or related field and 2+ years of Hardware Engineering or related work experience. OR Master's degree in Computer Science, Electrical/Electronics Engineering, Engineering, or related field and 1+ year of Hardware Engineering or related work experience. OR PhD in Computer Science, Electrical/Electronics Engineering, Engineering, or related field.

Job Area: Engineering Group, Engineering Group > Hardware Engineering General Summary: Digital Verification Engineer for IPs, ASICs and Chipsets used in Qualcomm Snapdragon power solutions. Qualcomm is a company of inventors that unlocked 5G ushering in an age of rapid acceleration in connectivity and new possibilities that will transform industries, create job s, and enrich lives. But this is just the beginning. It takes inventive minds with diverse skills, backgrounds, and cultures to transform 5Gs potential into world-changing technologies and products. This is the Invention Age and this is where you come in. Digital Verification Engineer for for Mixed-Signals IPs, ASICs and Chipsets used in Qualcomm Snapdragon power solutions. IPs include telemetry ADCs, 100W+ charging (Quick Charge 5.0), 5G power (mmW, envelope tracking, high performance low noise oscillators etc") and high efficiency power management (DC-DC charge pumps, bucks and linear regulators). * Work includes partnering with international teams in all stages of development from system definition to high-volume (100M+) OEM launches. * Digital Verification aspects include all stages of the verification process from test planning, UVM-compliant test-bench architecture, constrained-random stimulus creation, score-boarding and coverage closure. * Work includes verification of digital and mixed-signals IPs and exposure to analog behavioral models is a plus. * Work includes debugging of complex embedded systems including SOCs, firmware, embedded sequencers. * Position includes IP or chip DV ownership including task planning and project risk mitigation. * Work in a dynamic team environment with aggressive schedule towards metrics-based high quality target. Preferred Qualifications Strong troubleshooting skills across embedded systems disciplines (digital RTL, Firmware, analog behavioral models) Strong communication and organizational skills Strong process-oriented mindset. Expert-level System Verilog Programming Advanced UVM/SV (Universal Verification Methodology using System Verilog) Python or Perl scripting Minimum Qualifications Bachelor's degree in Science, Engineering, or related field. 4+ years ASIC design, verification, or related work experience Minimum Qualifications: Bachelor's degree in Computer Science, Electrical/Electronics Engineering, Engineering, or related field and 4+ years of Hardware Engineering or related work experience. OR Master's degree in Computer Science, Electrical/Electronics Engineering, Engineering, or related field and 3+ years of Hardware Engineering or related work experience. OR PhD in Computer Science, Electrical/Electronics Engineering, Engineering, or related field and 2+ years of Hardware Engineering or related work experience.

Job Area: Engineering Group, Engineering Group > Hardware Engineering General Summary: QCT's Bangalore Wireless R&D HW team is looking out for experienced HW design engineer to work on WRD IPs for Qualcomms best in class Mobile chipsets. Location Bangalore Roles and Responsibilities You will be contributing to flagship Wireless IP development covering WAN, WLAN, GNSS and Bluetooth technologies. You will be part of team defining and developing next generation Wireless R&D products. The candidate must have IP design experience preferably in wireless/DSP domain. The candidate must be strong in design micro-architecture & RTL coding (System Verilog or Verilog or VHDL). Other requirements are : Exposure to synthesis & STA Low power and high speed design awareness Knowledge on design flow, industry standard frond end tools flows ( lint, cdc, etc.) Knowledge of scripting and automationUnix/Linux shell programming, Perl, Python, Makefile etc. Strong critical thinking, problem solving and debug skills Good communication and interpersonal skills. Flexible to work with multi-geo team Minimum qualification Bachelors or Masters in Electrical/Electronics/Computers Science from reputed college/university. Years of experience 2- 4years Minimum Qualifications: Bachelor's degree in Computer Science, Electrical/Electronics Engineering, Engineering, or related field and 2+ years of Hardware Engineering or related work experience. OR Master's degree in Computer Science, Electrical/Electronics Engineering, Engineering, or related field and 1+ year of Hardware Engineering or related work experience. OR PhD in Computer Science, Electrical/Electronics Engineering, Engineering, or related field.

Job Area: Engineering Group, Engineering Group > Hardware Engineering General Summary: As a leading technology innovator, Qualcomm pushes the boundaries of what's possible to enable next-generation experiences and drives digital transformation to help create a smarter, connected future for all. As a Qualcomm Hardware Engineer, you will plan, design, optimize, verify, and test electronic systems, bring-up yield, circuits, mechanical systems, Digital/Analog/RF/optical systems, equipment and packaging, test systems, FPGA, and/or DSP systems that launch cutting-edge, world class products. Qualcomm Hardware Engineers collaborate with cross-functional teams to develop solutions and meet performance requirements. Minimum Qualifications: Bachelor's degree in Computer Science, Electrical/Electronics Engineering, Engineering, or related field. We are looking for bright ASIC design engineers with excellent analytical and technical skills. This is an excellent opportunity to be part of a fast paced team responsible for delivering Snapdragon CPU design, flows for high performance SoCs in sub-10nm process for Mobile, Compute and IOT market space. Job Responsibilities Participate on a project involved in the development of ASICs, with emphasis in Place and Route Implementation, Timing Closure, Low Power, Power Analysis and Physical Verification. Create design of experiments and do detailed PPA comparison analysis to improve quality of results, tuning recipes and setting course for the projects going forward Work closely with RTL design, Synthesis, low power, Thermal, Power analysis and Power estimation teams to optimize Performance, Power and Area(PPA) Tabulate metrics results for analysis comparison Develop Place & Route recipes for optimal PPA Minimum Qualifications 2+ years of High Performance core Place & Route and ASIC design Implementation work experience Preferred Qualifications Minimum 3+ years of experience in PD Extensive experience in Place & Route with FC or Innovus is an absolute must Complete ASIC flow with low power, performance and area optimization techniques Experience with STA using Primetime and/or Tempus is required Proficient in constraint generation and validation Experience of multiple power domain implementation with complex UPF/CPF definition required Formal verification experience (Formality/Conformal) Perl/Tcl, Python, C++ skills are needed Strong problem solving and ASIC development/debugging skills Experience with CPU micro-architecture and their critical path Low power implementation techniques experience High speed CPU implementation Clock Tree Implementation Techniques for High Speed Design Implementation are required Exposure to Constraint management tool and Verilog coding experience

Job Area: Engineering Group, Engineering Group > Hardware Engineering General Summary: Experience in Logic design /micro-architecture / RTL coding is a must . Must have hands on experience with SoC design and integration for SoCs. Experience in Verilog/System-Verilog is a must . Should have knowledge of AMBA protocols - AXI, AHB, APB, SoC clocking/reset/debug architecture and peripherals like USB, PCIE and SDCC. Understanding of Memory controller designs and microprocessors is an added advantage Hands on experience in constraint development and timing closure Work closely with the SoC verification and validation teams for pre/post Silicon debug Hands on experience in Low power SoC design is required Experience in Synthesis / Understanding of timing concepts for ASIC is required . Hands on experience in Multi Clock designs, Asynchronous interface is a must . Experience creating pad ring and working with the chip level floorplan team is an added advantage Experience in using the tools in ASIC development such as Lint, CDC, Design compiler and Primetime is required . Minimum Qualifications: Bachelor's degree in Computer Science, Electrical/Electronics Engineering, Engineering, or related field and 2+ years of Hardware Engineering or related work experience. OR Master's degree in Computer Science, Electrical/Electronics Engineering, Engineering, or related field and 1+ year of Hardware Engineering or related work experience. OR PhD in Computer Science, Electrical/Electronics Engineering, Engineering, or related field. 3-6 yrs of experience

Job Area: Engineering Group, Engineering Group > Hardware Applications Engineering General Summary: This position is for RTL designer role in DSP processor team. The position involves in-depth understanding of the ASIC design flow from RTL to GDS2 and the challenges posed by advanced technologies. The successful candidate will possess detailed understanding of RTL design, synthesis, static timing analysis, formal verification, PLDRC, clock domain crossing, and low power techniques. Knowledge and experience of microprocessor integration is a definite advantage. Skills/Experience Must have 3 to 15 years of practical experience with details of RTL development (VHDL and/or Verilog) including:functional and structural RTL design, design partitioning,simulation and regression, collaboration with design verification team. Must have good familiarity with latest RTL languages and tools, includingsimulation systems (e.g. Modelsim, VCS), synthesis tools (e.g. Design Compile), static timing tools (e.g. Prime Time), Linting tools, CDC tools, UPF, code coverage, System Verilog Assertion, etc. Experience with the following area is highly desirable Strong processor architecture knowledge Microarchitecture implementation Microprocessor integration Low power design Responsibilities Develop RTL for multiple logic blocks of a DSP core Run various frontend tools to check for linting, clock domain crossing, synthesis, etc. Work with physical design team on design constrain and timing closure Work with power team on power optimization Work with verification team to collaborate on test plan, coverage plan, and coverage closure Minimum Qualifications: Bachelor's degree in Electrical/Electronics Engineering, Computer Engineering, or related field and 3+ years of Hardware Applications Engineering or Hardware Design experience or related work experience. OR Master's degree in Electrical/Electronics Engineering, Computer Engineering, or related field and 2+ years of Hardware Applications Engineering or Hardware Design experience or related work experience. OR PhD in Electrical/Electronics Engineering, Computer Engineering, or related field and 1+ year of Hardware Applications Engineering or Hardware Design experience or related work experience.

Job Area: Engineering Group, Engineering Group > Hardware Engineering General Summary: Required Qualifications Bachelor's degree /masters degree in Electronics & Tele Engineering, Microelectronics, Computer Science, or related field. 9+ years RTL Design/Hardware Engineering experience or related work experience. Skills/Experience Required Strong Domain Knowledge on RTL Design , implementation, and integration. Experience with RTL coding using Verilog/VHDL/System Verilog. Experience in micro-architecture & designing cores and ASICs. Familiar with the Synthesis, Formal Verification, Linting, CDC, Low Power, UPFs, etc. Exposure in scripting (Pearl/Python/TCL). Strong debugging capabilities at simulation, emulation, and Silicon environments. Collaborate closely with cross-function team located in different time zone to research, design and implement performance and power management strategy for product roadmap. Good team player. Need to interact with the other teams/verification engineers proactively. Responsibilities Design and lead all Front-end design activities for Display Sub-system that deliver cutting edge solution for various Qualcomm business unit like VR, AR, Compute, IOT, Mobile. Perform RTL design, simulation, synthesis, timing analysis, lint check, clock domain crossing check, conformal low power check, and formal verification for IP blocks. Work closely with technology/circuit design team to close IP block specification/requirement. Work closely with verification/physical design team to complete the IP design implementation. Support SoC team to integrate Display Sub-system IP solution into various SoC chips and front-end design flows. Work closely with system/software/test team to enable the low power feature in wireless SoC product. Evaluate new low-power technologies and analyze their applications to address requirements. Understand and perform block & chip-level performance analysis & identify performance bottleneck and provide required solution. Minimum Qualifications: Bachelor's degree in Computer Science, Electrical/Electronics Engineering, Engineering, or related field and 6+ years of Hardware Engineering or related work experience. OR Master's degree in Computer Science, Electrical/Electronics Engineering, Engineering, or related field and 5+ years of Hardware Engineering or related work experience. OR PhD in Computer Science, Electrical/Electronics Engineering, Engineering, or related field and 4+ years of Hardware Engineering or related work experience.

Job Area: Engineering Group, Engineering Group > Hardware Engineering General Summary: As a leading technology innovator, Qualcomm pushes the boundaries of what's possible to enable next-generation experiences and drives digital transformation to help create a smarter, connected future for all. As a Qualcomm Hardware Engineer, you will plan, design, optimize, verify, and test electronic systems, bring-up yield, circuits, mechanical systems, Digital/Analog/RF/optical systems, equipment and packaging, test systems, FPGA, and/or DSP systems that launch cutting-edge, world class products. Qualcomm Hardware Engineers collaborate with cross-functional teams to develop solutions and meet performance requirements. Minimum Qualifications: Bachelor's degree in Computer Science, Electrical/Electronics Engineering, Engineering, or related field and 6+ years of Hardware Engineering or related work experience. OR Master's degree in Computer Science, Electrical/Electronics Engineering, Engineering, or related field and 5+ years of Hardware Engineering or related work experience. OR PhD in Computer Science, Electrical/Electronics Engineering, Engineering, or related field and 4+ years of Hardware Engineering or related work experience. Additional Qualcomm Noida CPU team is hiring for developing high performance and power optimized custom CPU cores. Individuals to Handle hardening complex HMs from RTL to GDS [ Synthesis, PNR, Timing ]. We are excited to add folks with us for the most cutting-edge work. Here, individuals would have the opportunity to work with some of the most talented and passionate engineers in the world to create designs that push the envelope on performance, energy efficiency and scalability. We offer a fun, creative and flexible work environment, with a shared vision to build products to change the world. Desired experience: 12+ years of experience in Physical design, STA. Solid understanding industry standard tools for physical implementation [ Genus, Innovus, FC, PT, Tempus, Voltas and redhawk]. Solid grip from floorplan to PRO and timing signoff along with understanding of IR drop and physical verification aspect. Should have experienced about preparing complex ECOs for timing convergence [ across huge set of corners] through Tweaker / Tempus / Physical PT ECOs. Should be aware about the tricks for minimizing power. Experience in deep submicron process technology nodes is strongly preferred. Knowledge of high performance and low power implementation methods is preferred. Willing to push PPA to the best possible extent. Strong fundamentals. Expertise in Perl, TCL language

Job Area: Engineering Group, Engineering Group > Hardware Engineering General Summary: As a leading technology innovator, Qualcomm pushes the boundaries of what's possible to enable next-generation experiences and drives digital transformation to help create a smarter, connected future for all. As a Qualcomm Hardware Engineer, you will plan, design, optimize, verify, and test electronic systems, bring-up yield, circuits, mechanical systems, Digital/Analog/RF/optical systems, equipment and packaging, test systems, FPGA, and/or DSP systems that launch cutting-edge, world class products. Qualcomm Hardware Engineers collaborate with cross-functional teams to develop solutions and meet performance requirements. Minimum Qualifications: Bachelor's degree in Computer Science, Electrical/Electronics Engineering, Engineering, or related field and 3+ years of Hardware Engineering or related work experience. OR Master's degree in Computer Science, Electrical/Electronics Engineering, Engineering, or related field and 2+ years of Hardware Engineering or related work experience. OR PhD in Computer Science, Electrical/Electronics Engineering, Engineering, or related field and 1+ year of Hardware Engineering or related work experience. Minimum of 5+ years experience in the area of DFT-, ATPG, Scan Insertion, MBIST, JTAG -In depth knowledge of DFT concepts. -In depth knowledge and hands on experience in DFT(scan/mbist) insertion, ATPG pattern generation/verification, mbist verification and post silicon bring up/yield analysis -Expertise in test mode timing constraints definition, knowledge in providing timing fixes/corrective actions for timing violations. -Ability to analyze and devise new tests for new technologies/custom RAM design/RMA etc. -Expertise in scripting languages such as perl, shell, etc. -Experience in simulating test vectors. -Knowledge of equivalence check and RTL lint tool (like spyglass). -Ability to work in an international team, dynamic environment -Ability to learn and adapt to new tools and methodologies. -Ability to do multi-tasking & work on several high priority designs in parallel. -Excellent problem-solving skills

Job Area: Engineering Group, Engineering Group > Hardware Engineering General Summary: This position is for RTL designer role in DSP processor team. The position involves in-depth understanding of the ASIC design flow from RTL to GDS2 and the challenges posed by advanced technologies. The successful candidate will possess detailed understanding of RTL design, synthesis, static timing analysis, formal verification, PLDRC, clock domain crossing, and low power techniques. Knowledge and experience of microprocessor integration is a definite advantage. Skills/Experience Must have 10 to 15 years of practical experience with details of RTL development (VHDL and/or Verilog) including:functional and structural RTL design, design partitioning,simulation and regression, collaboration with design verification team. Must have good familiarity with latest RTL languages and tools, includingsimulation systems (e.g. Modelsim, VCS), synthesis tools (e.g. Design Compile), static timing tools (e.g. Prime Time), Linting tools, CDC tools, UPF, code coverage, System Verilog Assertion, etc. Experience with the following area is highly desirable Strong processor architecture knowledge Microarchitecture implementation Microprocessor integration Low power design Responsibilities Develop RTL for multiple logic blocks of a DSP core Run various frontend tools to check for linting, clock domain crossing, synthesis, etc. Work with physical design team on design constrain and timing closure Work with power team on power optimization Work with verification team to collaborate on test plan, coverage plan, and coverage closure Minimum Qualifications: Bachelor's degree in Computer Science, Electrical/Electronics Engineering, Engineering, or related field and 6+ years of Hardware Engineering or related work experience. OR Master's degree in Computer Science, Electrical/Electronics Engineering, Engineering, or related field and 5+ years of Hardware Engineering or related work experience. OR PhD in Computer Science, Electrical/Electronics Engineering, Engineering, or related field and 4+ years of Hardware Engineering or related work experience.

Job Area: Engineering Group, Engineering Group > Hardware Engineering General Summary: You will be interacting closely with the product definition and architecture team. Developing implementation (microarchitecture and coding) strategies to meet quality, and PPAS (Performance Power Area Schedule) goals for Sub-system. Define various aspects of the block level design such as block diagram, interfaces, clocking, transaction flow, pipeline, low power etc. Perform as well as lead a team of engineers on RTL coding for Sub-system/SOC integration, function/performance simulation debug. Drive Lint/CDC/FV/UPF checks to ensure design quality. Develop Assertions as part of white-box testing-coverage. Work with stakeholders to discuss the right collateral quality and identify solutions/workarounds. Work towards delivering with key design collaterals (timing constraints, UPF etc.). Desired Skillset: Good understanding of low power microarchitecture techniques and AI/ML systems. Thorough knowledge of Computer system architecture, including design aspects of AI/ML designs. Experience in high performance design techniques and trade-offs in a Computer microarchitecture. Good understanding of principals of NoC Design Define Performance (Bandwidth, Latency) and Bus transactions sizing based on usecases across Voltage/Frequency corners Working with Power and Synthesis teams on usecases, dynamic power and datapath interactions Knowledge of Verilog / System Verilog. Experience with simulators and waveform debugging tools Working with SOC DFT and PD teams as part of collaterals exchanges Knowledge of logic design principles along with timing and power implications. Preferred Qualifications Master's or Bachelor's degree in Electronics or Electrical Engineering or equivalent. At least 3+ years of experience working on multiple designs. Minimum Qualifications: Bachelor's degree in Computer Science, Electrical/Electronics Engineering, Engineering, or related field and 2+ years of Hardware Engineering or related work experience. OR Master's degree in Computer Science, Electrical/Electronics Engineering, Engineering, or related field and 1+ year of Hardware Engineering or related work experience. OR PhD in Computer Science, Electrical/Electronics Engineering, Engineering, or related field.

Job Area: Engineering Group, Engineering Group > Hardware Engineering General Summary: As a leading technology innovator, Qualcomm pushes the boundaries of what's possible to enable next-generation experiences and drives digital transformation to help create a smarter, connected future for all. As a Qualcomm Hardware Engineer, you will plan, design, optimize, verify, and test electronic systems, bring-up yield, circuits, mechanical systems, Digital/Analog/RF/optical systems, equipment and packaging, test systems, FPGA, and/or DSP systems that launch cutting-edge, world class products. Qualcomm Hardware Engineers collaborate with cross-functional teams to develop solutions and meet performance requirements. Minimum Qualifications: Bachelor's degree in Computer Science, Electrical/Electronics Engineering, Engineering, or related field and 3+ years of Hardware Engineering or related work experience. OR Master's degree in Computer Science, Electrical/Electronics Engineering, Engineering, or related field and 2+ years of Hardware Engineering or related work experience. OR PhD in Computer Science, Electrical/Electronics Engineering, Engineering, or related field and 1+ year of Hardware Engineering or related work experience. Minimum of 5+ years experience in the area of DFT-, ATPG, Scan Insertion, MBIST, JTAG -In depth knowledge of DFT concepts. -In depth knowledge and hands on experience in DFT(scan/mbist) insertion, ATPG pattern generation/verification, mbist verification and post silicon bring up/yield analysis -Expertise in test mode timing constraints definition, knowledge in providing timing fixes/corrective actions for timing violations. -Ability to analyze and devise new tests for new technologies/custom RAM design/RMA etc. -Expertise in scripting languages such as perl, shell, etc. -Experience in simulating test vectors. -Knowledge of equivalence check and RTL lint tool (like spyglass). -Ability to work in an international team, dynamic environment -Ability to learn and adapt to new tools and methodologies. -Ability to do multi-tasking & work on several high priority designs in parallel. -Excellent problem-solving skills