23 Lpt Jobs

To coordinate, conduct, and documentNon-Destructive Testing (NDT) activities across all welding stages and projectrequirements , ensuring that all jobs meet therelevant code, client standards, and acceptance criteria without delaying flowor compromising safety. Key Responsibilities 1. Plan and coordinate NDT testing (in-house oroutsourced) for all welds as per project specifications, ITPs, andclient-approved procedures. 2. Ensure the availability and readiness of NDT personnel,tools, and documentation before the job reaches its inspection stage. 3. Carry out or coordinate the following NDT methods asapplicable: o VisualTesting (VT) primary inspection of weld bead, surfacedefects, undercut, and overlap o LiquidPenetrant Testing (LPT/DPT) for surface cracks in filletwelds, corner joints, and SS jobs o MagneticParticle Testing (MPT) for ferromagnetic jobs (lessapplicable in SS, but relevant for any MS assemblies) o UltrasonicTesting (UT) for subsurface and volumetric inspection incritical butt joints or heavy welds o RadiographicTesting (RT/X-ray) for full-penetration welds where specifiedby client or code o PositiveMaterial Identification (PMI) for material mix-up preventionin high-specification SS components o Hardness,Ferrite, or Surface Roughness Checks where required byQA/Welding Expert or client 4. Ensure tests are conducted only after job is fullyready avoid premature offers or repeated attempts. 5. Mark and isolate jobs pending NDT prevent them fromproceeding to next stage until cleared. 6. Coordinate with third-party agencies for witnessing andapproval where needed. 7. Maintain NDT reports, maps, and traceability documentsin proper formats linked to job ID, weld ID, operator ID, and shift. 8. Escalate repeat failures, inconsistent readings, ortest rejections to QC Lead and Welding Expert for investigation. 9. Monitor equipment calibration, validity of NDT agencyapprovals, and Level II/III certification documents. 10. Provideinspection data during client audits and walkdowns; support QA in maintainingNDT records in ISO or client formats. 11. Supporttraining of junior QC staff on NDT interpretation and reporting discipline. Responsibilities Outsidethe Scope of This Role Does not interpret test standards oraccept/reject results independently unless certified escalates to LevelII/III or QC Lead as required Does not perform welding, rework, or repair only validates results and traceability Does not schedule project flow tests must alignwith fabrication sequence and readiness Does not control quality systems but ensurestesting aligns with QA-defined ITP and project specs Qualifications Experience Diploma or B.Tech in Mechanical / Metallurgy /Welding Engineering / NDT Technician 2 + years of experience in NDT coordination or execution in fabrication or EPC projects NDT Level IIcertification (at minimum) in VT and LPT; UTand RT preferred Familiarity with ASME, AWS, EN, and ISOstandards applicable to SS fabrication Experience coordinating outsourced NDT orin-house lab teams Strong understanding of NDT documentation,mapping, and traceability Good communication for the client, agency, andshift coordination Preferred: Experience in stainless steel or infrastructure fabrication setup

We have openings for Lead NDT Engineer - Barmer Qualification : B.E/B.Tech - Mechanical Industry : Oil & Gas Experience : min 15+ years Certifications : NDT Level 2 Job Description : * Should have experience in Oil & Gas EPC/Refinery construction project. Location : Barmer If your interested for this position send your updated cv along with below details to kcharishma@meghaeng.com Total Exp: Relevant Exp : Qualification : DOB : Age : Current Company : Current location : Native : Current CTC : Expected CTC : Notice Period : Willing to relocate for Barmer location. Reason for job change: Note: 1 : Mandatory to have min 15 years exp in EPC Companies NDT Execution and all previous companies experience letters 2. Only Relevant candidate will be contacted.

We have openings for Lead NDT Engineer - Barmer, Barauni Qualification : B.E/B.Tech - Mechanical Industry : Oil & Gas Experience : min 15+ years Certifications : NDT Level 2 Job Description : 1. 15+ years of experience in NDT (refinery/petrochemical projects) 2. Plan and execute NDT activities for refinery site execution 3. Ensure compliance with project specs, industry standards, and regulations 4. Develop and implement NDT procedures and protocols 5. Conduct and supervise NDT testing (RT, UT, MT, PT, etc.) 6. Interpret and evaluate NDT test results 7. Identify and report defects and discrepancies 8. Collaborate with construction and quality teams 9. Ensure safety and quality standards are met for NDT activities 10. Manage and maintain NDT equipment and calibration records 11. Prepare and submit NDT reports and documentation 12. Strong knowledge of NDT methods and techniques 13. Certification in NDT methods (ASNT Level II or equivalent) Location : Barmer, Barauni If your interested for this position send your updated cv along with below details to kcharishma@meghaeng.com Total Exp: Relevant Exp : Qualification : DOB : Age : Current Company : Current location : Native : Current CTC : Expected CTC : Notice Period : Willing to relocate for Barmer, Barauni location. Reason for job change: Note: 1 : Mandatory to have min 15 years exp in EPC Companies NDT Execution and all previous companies experience letters 2. Only Relevant candidate will be contacted. Thanks & Regards, Charishma . K HR Department Megha Engineering & Infrastructure Ltd

Post- Senior Engineer and Assistant Manager Email - punejobs02@gmail.com Contact - 9356395439 Location - Pune Chakan Alandi Phata Education: A degree in engineering, manufacturing, or a related field is often preferred. Experience: 8 to 10 Year Prior experience in quality assurance or fabrication, Heavy fabrication, NDT, Powder coating, Painting environment is typically required. Technical Skills: Knowledge of quality control methodologies, tools (like Six Sigma,7QC Tool), and fabrication processes. Role & responsibilities Key Roles and Responsibilities 1. Quality Assurance Oversight: Assist in developing and implementing quality assurance processes and standards. Conduct regular audits and inspections of fabrication processes to ensure compliance with quality standards. 2. Team Management: Supervise quality control inspectors and technicians. Train staff on quality control procedures and standards. 3. Data Analysis: Analyze quality control data to identify trends, defects, and areas for improvement. Prepare reports on quality metrics for management review. 4. Problem Solving: Investigate quality issues and coordinate with fabrication teams to implement corrective actions. Facilitate root cause analysis for defects and non-conformances. 5. Documentation and Compliance: Maintain accurate records of inspections, tests, and quality control activities. Ensure compliance with industry standards, regulations, and company policies. 6. Collaboration: Work closely with engineering, production, and supply chain teams to enhance product quality. Participate in cross-functional teams to improve fabrication processes. 7. Continuous Improvement: Drive initiatives for continuous improvement in quality processes and systems. Stay updated on industry trends and best practices in quality management. 8. Customer Interaction: Address customer complaints related to product quality and provide timely resolutions. Gather feedback from customers to inform quality improvements.

Responsibilities / Tasks General Information Goal: The Global Engineering Pool in India is committed to deliver skilled resources to support projects and Internal standardization activities with in GEA for LPT as well as other GEA divisions with ultimate aim of generating potential savings for GEA by utilization of low-cost resources. Role & Responsibilities Electrical Design Validation Ensure Electrical compliance with customer specification Ensure to meet project deadlines Various Documentation - Electrical and Instrumentations Co-ordination with Electrical Team and support each other Co-ordination with Internal Customer and fulfill their requirements Your Profile / Qualifications Bachelor of Engineering Degree in Electrical, Electronics, Instrumentation & Controls or similar education background Work Experience - Engineer - Electrical 4-7 year Experience on any particular Dairy / Food / Beverages / Brewery / Pharma / Chemical Industry Skills - Engineer - Electrical Electrical Engineering Know-how Depth Knowledge of Eplan P8 Software - Like Master database & Reports, Electrical Schematics Depth knowledge of PLC hardware and field connection with siemens & Rockwell make PLCs Machinery standard IEC-60204 Know-how Switchgear assembly standard IEC-61439 Know-how Strong interpersonal communication skills and co-ordinations with various project teams Cables / busbar calculation & sizing Selection of components for hazardous area electrical and instrumentation Knowledge of heat-loss calculation Knowledge of UL / CE / ATEX / IP standards for control panels and field instrumentation Strong knowledge of field instrumentation and connections with PLC hardware Task Engineer - Electrical Electrical Loop drawings, Panel Design & Layout, Engineering with EPLAN P8 Prepare Instrumentations & Hook-up Drawings Design Control System, Configure Industrial Network Architecture Wiring Schematics for Switchboard and Control Panels Cable Calculations and Cable tray layout Loop drawing generation with EPLAN P8 EEC module Languages known Must have English Good to have Regional Language Preferred Hindi Travel Requirements The Engineer would be based in India office Limited travel will be required, Involving in Electrical site support, Panel FAT throughout India & abroad. Other Qualifications Computer literacy with Mail Outlook, Teams Microsoft Office Products Good to have MS Project Basic IT skills Did we spark your interest Then please click apply above to access our guided application process.

You will be joining the Quality team at Konecranes, focusing on Quality Management in the manufacturing and service industry. Your responsibilities will include managing Quality at the Distribution Centre, covering Inbound & Supplier quality, NC management, HSEQ Documentation & Audits. Your main duties will involve incoming and supplier end inspections, verification of supplier documents, preparation of QAP/ITP, and ensuring compliance with ISO standards and corporate guidelines for HSEQ Systems. You will also be responsible for monitoring internal HSEQ KPIs, Procedures, handling rejection analysis, supplier rating, and providing support to improve supplier quality performance. Other tasks include Quality MIS, material inward and transfer in SAP, and NC Handling. To qualify for this role, you should have a Degree/Diploma in mechanical engineering or equivalent with 8 to 10 years of experience in QA/QC/SQA. Essential skills include knowledge of casting, forging, fabrication & machined components, understanding of manufacturing processes and standards, ability to read mechanical and electrical drawings, hands-on experience in preparation of QAP, RCA, and 8D. Familiarity with NDT techniques like UT, LPT, RT interpretation, and knowledge of Systems like SAP/Sible are preferred. Experience in the crane industry, material handling systems, or machine manufacturing is a plus, along with knowledge of ISO standards. This position offers the opportunity to work with the Parts Distribution Centre of Konecranes and Demag Pvt Ltd., supporting after-sales service and modernization business units. You will have exposure to advanced technology in material movement safety and various product commodities. There are also internal growth opportunities available for enhancing your competencies in the respective job domain. If you are interested in this role, please submit your CV via the Apply now button by the specified date. Early applications are appreciated as interviews will be conducted continuously until a suitable candidate is selected. For any queries, you can contact the recruiting manager or recruiter using the provided contact information. Konecranes is a global leader in material handling solutions, committed to providing a safe, productive, and sustainable environment. We prioritize fairness and a discrimination-free workplace for all employees and job applicants.,

Desired Skills Knowledge:Knowledge of ASME, TEMA, EIL, EN, IS-codes, etc. Skills :CSWIP 3.1/ AWS-CWI/ IWE certification is mandatory, EN 9712 VT Level 2 is mandatory, NDT Level II (RT, UT, MT, VT, LPT) Role & Responsibilities Familiar with Pressure Vessel, Heat Exchangers and Piping inspections and documentations. Welding inspection techniques, Preparation and approval of WPS, PQR, WPQ, Preparation of Weld maps and Weld Test Plans (WTP) are mandatory. Knowledge of Welding and cutting processes, PWHT cycle, Welding techniques, and welding sequencing is desired. Knowledge of ASME, AWS and EN codes is desired. ASNT NDT (PT, RT, MT, UT, VT) Level II certification. Knowledge about quality Procedures Inhouse & Outside Inspection & expediting at vendor place Offering the equipment/s for TPIA/Client inspection and testing. Customer complaint Role & responsibilities Preferred candidate profile - Experience - Min. 10-15 Years Preferred Industry- Oil & Gas / Refining / Petrochemicals/ Chemical Education/Qualification- Min: Diploma/BE/ME Mechanical

Standards & Codes: ASME Section VIII Div. 1 & 2 ASME Section IX (Welding Qualifications ASME Sec V Welding & NDT: Welding process knowledge (SMAW, GTAW, SAW) WPS/PQR/Welder qualifications Non-Destructive Testing (RT, UT, PT, MT, VT) knowledge Interpretation of NDT results Fabrication & Inspection: Dimensional inspection of shells, heads, nozzles Monitoring fit-up and alignment (e.g., weld mismatch tolerances) Hydrostatic / pneumatic testing procedures Surface preparation and painting/coating inspection Materials: Review of Mill Test Certificates Traceability & material control Handling special alloys (e.g., stainless, Hastelloy) Documentation: Preparing Quality Dossiers / Manufacturers Data Reports Reviewing MDRs, ITPs (Inspection & Test Plans), QAPs Familiarity with project documentation control systems Software & Tools Proficiency with MS Office (Excel, Word) Experience with ERP/QMS systems (SAP, Oracle, etc.) Use of inspection instruments (micrometers, ultrasonic thickness gauges) Core Competencies Strong understanding of pressure vessel manufacturing workflows Ability to read and interpret fabrication drawings Knowledge of welding metallurgy and defects Understanding of calibration systems and control of measuring instruments Soft Skills Attention to detail and record-keeping Strong communication (to interface with clients and third-party inspectors) Problem-solving approach to NCRs and root cause analysis (RCA) Preferred / Desirable ASNT Level II Certification in at least 2 NDT methods Knowledge of ISO 9001 and ASME U-Stamp compliance

Responsibilities / Tasks General Information Goal: The Global Engineering Pool in India is committed to deliver skilled resources to support projects and Internal standardization activities with in GEA for LPT as well as other GEA divisions with ultimate aim of generating potential savings for GEA by utilization of low-cost resources. Role & Responsibilities Electrical Design Validation Ensure Electrical compliance with customer specification Ensure to meet project deadlines Various Documentation - Electrical and Instrumentations Co-ordination with Electrical Team and support each other Co-ordination with Internal Customer and fulfill their requirements Your Profile / Qualifications Bachelor of Engineering Degree in Electrical, Electronics, Instrumentation & Controls or similar education background Work Experience - Engineer - Electrical 3-7 year Experience on any particular Dairy / Food / Beverages / Brewery / Pharma / Chemical Industry Skills - Engineer - Electrical Electrical Engineering Know-how Depth Knowledge of Eplan P8 Software - Like Master database & Reports, Electrical Schematics Depth knowledge of PLC hardware and field connection with siemens & Rockwell make PLCs Machinery standard IEC-60204 Know-how Switchgear assembly standard IEC-61439 Know-how Strong interpersonal communication skills and co-ordinations with various project teams Cables / busbar calculation & sizing Selection of components for hazardous area electrical and instrumentation Knowledge of heat-loss calculation Knowledge of UL / CE / ATEX / IP standards for control panels and field instrumentation Strong knowledge of field instrumentation and connections with PLC hardware Task - Engineer - Electrical Electrical Loop drawings, Panel Design & Layout, Engineering with EPLAN P8 Prepare Instrumentations & Hook-up Drawings Design Control System, Configure Industrial Network Architecture Wiring Schematics for Switchboard and Control Panels Cable Calculations and Cable tray layout Loop drawing generation with EPLAN P8 EEC module Languages known Must have English Good to have Regional Language Preferred Hindi Travel Requirements The Engineer would be based in India office Limited travel will be required, Involving in Electrical site support, Panel FAT throughout India & abroad. Other Qualifications Computer literacy with Mail Outlook, Teams Microsoft Office Products Good to have MS Project Basic IT skills Did we spark your interest? Then please click apply above to access our guided application process.

Responsibilities / Tasks General Information The Global Engineering Pool in India is committed to deliver skilled resources to support projects and Internal standardization activities with in GEA for LPT as well as other GEA divisions with ultimate aim of generating potential savings for GEA by utilization of low-cost resources. Role & Responsibilities Electrical Design Validation Ensure Electrical compliance with customer specification Ensure to meet project deadlines Various Documentation - Electrical and Instrumentations Co-ordination with Electrical Team and support each other Co-ordination with Internal Customer and fulfill their requirements Electrical Installation Supervision and Validation on site Your Profile / Qualifications Bachelor of Engineering Degree in Electrical, Electronics, Instrumentation & Controls or similar education background Work Experience - Engineer - Electrical 3-7 years of experience in the Dairy / Food / Beverages / Brewery / Pharma / Chemical Industry Exposure to UL508A Skills - Engineer - Electrical Electrical Engineering Know-how In-depth Knowledge of AutoCAD Electrical Software - Symbol library, Foot Prints, Electrical Symbols and Electrical Schematics In-depth Knowledge of P&ID Software - Symbol library, P&ID database understand and prepare P&ID based on the markups UL and CSA Standards Know-how NEC standards Know-how In-depth knowledge on selection of Electrical components for various types of control panels Knowledge of Eplan P8 Software would be as added advantage - Like Master database & Reports, Electrical Schematics Strong interpersonal communication skills and co-ordinations with various project teams Task - Engineer - Electrical Electrical Panel Design & Layout, Engineering with AutoCAD Electrical Prepare Instrumentations & Hookup Drawings Design Control System, Configure Industrial Network Architecture Wiring Schematics for Switchboard and Control Panels Cable Calculations and Cable tray layout Panel Load calculations control Panels Heat Loss calculation of Motor control Panels Languages known Must be proficient in English (verbal/written) Good to have Regional Language Preferred Hindi Travel Requirements The Engineer would be based in India office Limited travel will be required, Involving in Electrical site support, Panel FAT throughout India & abroad. Other Qualifications Computer literacy with Mail Outlook, Teams Microsoft Office Products Good to have MS Project Basic IT skills Did we spark your interest? Then please click apply above to access our guided application process.

Responsibilities / Tasks THE POSITION To provide Design/ detail Engineering and other technical support in the preparation/presentation of proposals and projects. The key priorities for the role: Upon securing a contract / order the incumbent (depending upon the size and complexity of the project) may be required to operate independently or as part of a project team to develop General arrangement and Fabrication /manufacturing of Components, Structures Ducting as well as other document s/drawings for the project. The tasks and responsibilities for the role include: Hands on Design experience of Food/ Beverages/ Dairy equipment like Tanks (Atmospheric /pressurized and jacketed), Shell and tube type condenser and callendria, ducting system is highly desirable. Ability to understand the Design analysis report Generated on Design software/ program, Manual or MS office base and Design code. Knowledge about Equipment, Ducting, Structure Etc. Hi-proficiency in Autodesk Inventor, Autodesk Vault, AutoCAD mechanical, Work cooperatively with the team of engineers and technical staff in the Business Unit in the preparation of quotations and execution of projects as and when required. Create drawings from basic 2D/3D required to complete a project; drawing multiple views of the system, components/Equipment, and parts; depicting relationship of components and parts; identifying dimensions, angles, curvatures, tolerances, and materials. Participate in the review of plant, equipment and structures as required. Schedule and control own workflow to meet deadline commitments. Undertake control of design and drafting for small to medium sized projects as required. Preserve and improve design knowledge and experience. Check prints by utilizing GEA checking procedures. Work cooperatively with the Company administrative staff. Develop the Drawings according to given sketches, P&ID s, layout, and specifications under the direction of engineering team. Administration Maintain appropriate records by filing drawings, project notes and specifications using the local regions filing procedures. Keep up to date on all new products, product changes and general processing trends. Prepare weekly timesheets and project reports. Assist in other parts of the Companys business as required to ensure the overall effectiveness of the Company. Travel Requirements: The Engineer will be based in Vadodara Office. Travel Which may involve extended periods stay on sites, throughout India location, may require based on Project requirement. Key Relationships: Members of LPT-10.1.2.2 Technical design Teams Sr. Manager: LPT-10.1.2.2.1 Component Design 1 India Director Technical Design: LPT-10.1.2 Global Engineering Pool India LPT Matrix Organization Your Profile / Qualifications CANDIDATE PROFILE Technical Designer should be detail oriented, possess good English language communication skills, both verbal and written. Must be self-motivated. Must possess good interpersonal skills and work well in a team setting as well as independently as required. Qualification: Degree/Diploma mechanical Engineer Experience Minimum 6 to 8 years of work experience in the field of mechanical design Engineering. Required languages Full working proficiency in English Software proficiency Autodesk Inventor Autodesk Mechanical Autodesk Vault Relevant work experience Hands on experience in design and detailing of Hygienic Equipment Design for Dairy/ Food/ Beverages, Ducting system/ Structural steel is highly desirable Mechanical Drawing of Equipment, Ducting, structure, P&ID, Layout, piping Etc. Detail drawing and dimensioning according to all international and Indian standard. Other Skills required. Computer literacy with demonstrated experience in using the Internet, Microsoft Office (i.e., Word, Excel), MS Project preferred Etc.. Interpersonal skills: Part of a team with a common design sense. Needs to be able to communicate openly their criteria and accept new designs and improvements analyzing advantages and disadvantages in an objective manner but also taking care of aesthetical aspects. Needs to be able to persuade the client (internal or external) for getting a GEA fingerprint in the design but respecting their preferences. Needs to be creative and innovative but taking care about learned lessons. Ability to communicate within the organization to all levels. Communication requirements for the role: Internal stakeholders: GEA Site, Project, Quality and HSE Managers, Project Engineering, Regional Sales, Technical design teams, Global Engineering pool teams, Supply chain and Logistics. External stakeholders: Customers Site, HSE and Quality managers, GEA sub suppliers. Type of communication: Face to Face, email and online meetings will be used to negotiate and harmonize internal/external stakeholders about successful project delivery. Did we spark your interest? Then please click apply above to access our guided application process.

Focus expertise Major exposure to welding and welded components and products and related testing and expertise Good command in Welding like TIG,MIG,GMA,FMA Welding process, Preparing WPS , Finding the defect on welding and correcting it. Preparing welding procedure and testing follow the standard of EN-15085,ISO-5817,ISO-14002-3,ISO-15607 Detect the welding defect and drive welding quality with vendor and adhereing to WPS Expertise in welding inspections through Radiography, visual inspections ,performed LPT testing DPT testing Ability to work closely with welders and driving product quality 1. To ensure all the products, processes and suppliers (Internal and External) are in line with organisational guidelines/SOP laid for quality and QMS and certification requirements 2. To Investigate, analyze and resolve supplier quality problems by conducting audits, analyzing defect trends and leading continuous improvement projects. 3. Liasioning with various certifying agencies to organise and achieve various product/compliance certifications 4. Handling Third Party Customer Inspections Experience:- experience in QA/QC with promising experience in spearheading Supplier & Product Quality as well as handling ISO 9001:2008/2015 QMS Audits and other audits certifications for OEM environment with in-depth exposure of EPDM/Rubber components, welding, die-casting, fabrication, tooling, injection molding, various surface treatment process viz. galvanisation, powder coating, nickel plating, etc. Responsibilities (A) Supplier Product Quality :- 1. Work with Purchase/VD to ensure supplier performance is regularly reported and that appropriate and timely corrective actions are implemented 2. Handle Incoming, In-process and Final inspections

We are looking for someone who has good hands on experience in VAPT. This role is with one of the government department of Maharashtra. Education: B.E/B. Tech / M.Sc. (Comp. Sci) / MCA / MBA/ M. Tech degree or equivalent. Should be a certified auditor. 6 or more years of overall experience with at least 6 years of relevant experience in Vulnerability Analysis, Penetration Testing and/or forensics. Must have experience in managing at least 3 projects for large, enterprise scale Clients. should have at least two industry certifications as mentioned below: 1. Licensed Penetration Tester (LPT) 2. Certified Penetration Testing Professional (CPENT) 3. Certified Expert Penetration Tester (CEPT) 4. GIAC Penetration Tester (GPEN) 5. CompTIA PenTest+ 6. Certified Ethical Hacker (CEH) 7. Certified Mobile and Web App Penetration Tester (CMWAPT) 8. Computer Hacking Forensic Investigator (CHFI) 9. Certified Information System Auditor (CISA) 10. Certified Information Security Manager (CISM) 11. Other acceptable industry related certification in VAPT. 12. OSCP

SUMMARY Knowledge of OHS related to welding Evaluate designs for welding requirements and ensure they meet structural integrity and quality standards Create and qualify PQR and WPS for different materials and weld techniques Design and develop modern welding systems Cobot, Robot Conversant with EN, ISO & ASME Codes. Identifying and resolving issues related to welding process and weld quality. Conducting process audit and process revalidation in defined frequency Requirements Qualified IWE Able to perform VT, PT, MPT, UT & radiography having ASNT level III certificate. Develop PQR and WPS Understanding the properties and behavior of different metals and alloys during welding. Hands on experience in various welding techniques, having experience in implementing welding automation projects Benefits Proactive weld quality improvement reducing weld related failures and rework. This will cover welding expertise in future business growth plans Build quality improvement

Responsibilities: * Conduct UT inspections using Modsonic equipment * Perform LPT tests on welds and materials * Operate MPV systems during construction phases * Follow ASNT Level II procedures for NDT techniques Cafeteria Travel allowance

We are seeking a detail-oriented and experienced QA/QC Engineer to join our manufacturing team. The ideal candidate will be responsible for ensuring that our products meet the highest quality standards and comply with industry regulations. Key Responsibilities : Develop and implement quality control procedures and processes. Develop QAP / ITP with required procedures and get customer approvals for projects Conduct inspections and tests throughout the manufacturing process. Manage inspections with customers and TPI Manage quality team to ensure meeting orders CDD while ensuring all quality requirements are met with the highest standard Co-ordinate and expedite materials to ensure timely delivery of jobs, ensure receiving timely dispatch clearance from customers Prepare final documents and dossier sets and ensure customer approvals for final submissions Analyze data and prepare reports on quality metrics and trends. Identify areas for improvement in the production process and implement corrective actions. Collaborate with production teams to resolve quality issues and enhance product reliability. Ensure compliance with industry standards and regulatory requirements. Maintain documentation of quality assurance activities and audits like WPS PQR, calibration, etc. Managing audits by customers and various TPI agencies. Qualifications : Bachelors Degree in Mechanical Engineering or Diploma in Mechanical Engineering. Minimum of 10 years of experience in QA/QC within a manufacturing environment for pressure vessels or filters and strainers Experience in managing teams to ensure smooth work of the Quality department Strong knowledge of quality control methodologies and tools. Experience in working with customers such as IOCL, EIL, NTPC, NPCIL, BHEL, etc Proficient in using measuring and testing equipment. Familiarity with ISO standards and other relevant quality frameworks. Knowledge of ASME codes, material grades, welding process, painting & its testing requirement. NDT Level II in RT, DPT, MPT & UT. Able to review MTC with respective standard & specification. Strong communication and interpersonal skills. Ability to work effectively in a team environment.

Responsibilities: * Conduct NDT inspections using ASNT Level II techniques on RT, UT, PT & LPT equipment * Document results accurately and timely * Collaborate with production team to resolve issues found during inspection Over time allowance House rent allowance Health insurance Employee state insurance Provident fund

Role & responsibilities :- Hands on in Planning and follow up various materials. Need to be very good in excel Knowledge of Micros is added advantage Knowledge of SAP is added advantage Good verbal and written communication skills. Knowledgeable in Vendor Development predominantly of SG Iron Castings and its Machining Pattern manufacturing SG Iron Castings Machining of Castings Knowledge of Inspection of components at Vendors end. Knowledge of vendors for various SGI Castings and their Machining around Pune and Kolhapur. Knowledge of vendor base for Aluminium Gravity and Pressure Die casting and its machining is added advantage. Knowledge on following related to castings Non Destructive testing Radiography, LPT, MPI, UT Destructive Test Chemical, Mechanical. Good in negotiation skills and related commercial aspects.

Responsibilities: * Conduct mechanical inspections using NDT methods. * Ensure compliance with QC engineering standards. * Perform UT, RT, PT, VT, MPT, painting, and LPT tests. * Collaborate on quality assurance initiatives. Travel allowance Accidental insurance

Here's an updated version of the job description, incorporating your specified details: Staff Product Security Engineer (Embedded & IoT) Work Flexibility: Hybrid Work Mode: Hybrid Location: Bengaluru Work Flexibility Definitions: Remote Role allows you to work the majority to 100% of time from an alternate workplace. These roles could have travel expectations, and you must work within the country of the job requisition location. Field-based – You can expect to regularly work a majority to 100% of time at customer facilities and has a set territory or expectation to travel within a set boundary. Almost all sales roles would likely be qualified as field-based. Onsite – Role is 100% located at a company facility. Some ad hoc flexibility may be available depending on role, level, and job requirements. Manufacturing roles and any role that requires physical presence at the office would qualify under this category. Hybrid – You can expect to regularly work in both an alternate workplace and a company facility. Roles that are partially remote or co-located would qualify as hybrid, and the expectation to be on site would be defined and agreed upon by your manager/supervisor. What you will do: Provide technical leadership and guidance to a team of Web, Embedded, and IoT Security engineers. Execute and oversee Penetration Testing and Vulnerability Assessment activities for Embedded Systems and IoT devices. Leverage DevSecOps to embed security testing ( SAST, DAST, Host Scanning, ATO Scanning, SBOM Generation ) into all phases of the Software Development Life Cycle (SDLC). Develop/review technical documentation (procedures/work instructions/guidance documents) for technical services. Develop and maintain comprehensive test plans, methodologies, and tools for security testing. Conduct in-depth analysis of security vulnerabilities and propose mitigation strategies. Collaborate with cross-functional teams to design and implement secure Embedded and IoT solutions. Lead the Software Bill of Materials (SBOM) Management program , ensuring accurate identification and documentation of software components and dependencies. Drive continuous improvement initiatives related to Embedded and IoT security, testing, and vulnerability management. What you need: Required Qualifications: Bachelor's or Master’s in Computer Science Engineering or a related field. 4 to 10 years of experience in product security, with a strong focus on embedded systems and IoT . Experience with threat modeling, risk assessment , and security architecture reviews for Embedded Systems and IoT solutions. Proficiency in C, C++, and Python programming languages. Familiarity with relevant security standards and frameworks such as OWASP, NIST Cybersecurity Framework , and ISO 27001 . Solid understanding of software development lifecycles and methodologies, particularly in the Embedded Systems and IoT context. Preferred Qualifications: Proficiency in using security testing tools such as Burp Suite, Wireshark, Nessus, and Metasploit , and experience applying DevSecOps principles. Experience in automation of routine tasks using tools like Jenkins and/or scripting languages such as PowerShell, Ruby, or Python. Understanding of Cloud-based environments like Azure and AWS . At least one professional certification like ECSA Practical/CPENT/LPT/OSCP/OSWE/OSCE or similar involving practical exams. Additional Details: Travel Percentage: 10% Mode of Interview: Face-to-Face

Job Title: Welding and NDT Engineer Location: Kothrud, Pune & Vadodara, Gujarat Employment Type: Full-Time Experience: 2-5 Years (Freshers with relevant certifications may also apply) Job summary We are looking for a skilled Welding and NDT Engineer to join our growing team at Tecknowcon Services. The ideal candidate will be responsible for overseeing welding activities, conducting non-destructive testing (NDT), ensuring compliance with industry standards, and maintaining the highest levels of quality assurance and control across projects. Key Responsibilities Develop, review, and approve Welding Procedure Specifications (WPS), WPQR, and welder qualifications as per international standards (ASME, ISO, EN, etc.) Perform and supervise NDT methods including UT, RT, MT, PT, and VT Interpret NDT results and prepare detailed inspection and testing reports Ensure compliance with applicable codes and standards (ISO 3834, EN 1090, EN 15085, ASME) Conduct audits and quality checks at vendor and site locations Support training and qualification of welders and NDT personnel Qualifications & Skills: Degree/Diploma in Mechanical/Metallurgical Engineering Knowledge of welding standards and procedures (IWE/IWT preferred) Hands-on experience with welding inspections and NDT techniques Good understanding of QA/QC protocols Strong analytical and report-writing skills Willingness to travel for field/site inspections Benefits Exposure to domestic and international projects Opportunities for certification and skill development Dynamic and supportive work environment Competitive salary and travel allowances

Carry out NDT and prepare required reports Coordinate with external service providers for radiographic testing, evaluate results and prepare reports Coordinate with external labs for chemical and mechanical testing Maintain records of all NDT conducted across products Review and highlight non-conforming products and deviations Position Requirements: Incumbent with minimum 5 years experience NDT Level 2 certification is required. Should be qualified experienced in the following 4 techniques- UT (ultrasonic Testing) RT (Radiographic Testing) MPT (Magnetic Particle testing ) DPT/LPT (Dye/Liquid Penetrant Testing) UT (ultrasonic Testing) RT (Radiographic Testing) MPT (Magnetic Particle testing ) DPT/LPT (Dye/Liquid Penetrant Testing) Should hold a Diploma in Any Specialization, B.Tech/ B.E. in Any Specialization.

Role & responsibilities Carry out NDT and prepare required reports Coordinate with external service providers for radiographic testing, evaluate results and prepare reports Coordinate with external labs for chemical and mechanical testing Maintain records of all NDT conducted across products Review and highlight non-conforming products and deviations Preferred candidate profile Incumbent with minimum 5 years experience &NDT Level 2 certification is required. Should be qualified & experienced minimum in the following 4 techniques. UT (ultrasonic Testing) RT (Radiographic Testing) MPT (Magnetic Particle testing ) DPT/LPT (Dye/Liquid Penetrant Testing)