335 Equipment Layout Jobs - Page 3

Candidates should have 5 to 10+ years of extensive experience in design & engineering works related to EHV/HV Substations, DRPC/SVC Stations, OHTL & Underground distribution, renewable power plants (solar, wind etc.) Experience in Power plants including PV Plants, HVDC System will be added advantage. Candidate Shall be familiar with local and international standards. Familiarity with SEC standards and practices is an advantage. Applicants should be experienced users of AutoCAD, Micro Station, and other relevant drafting softwares. Experience in 3D softwares is an advantage.Broad understanding of Substation equipment arrangements. Responsible to Deliver accurate and thorough designs that meet...

Below is the Job Description for PHE / FF Draftsman :Knowledge of AutoCAD 2021, Revit, and other services knowledge of infra coordinationPreparation of Basement surface drain & sub-soil drain Designing of External sewage & Storm water drainage system Preparation of water supply schematic, drainage schematicUnderground water tank and Overhead water tank plan and sections with sleeve detailsCo-ordination in drawings of engineering servicesTo draw and prepare Wall elevation, Sections of PlumbingQuantity take-off sheet for Firefighting, and plumbing, Design and drafting, calculation of water balance sheet, water tank sizingTender drawing preparation, List of drawings, typical detail drawings Dra...

Responsible for:Estimating Electrical loads, lighting loads, normal / Emergency loads Layout of the Switch gear rooms Sizing of HT/LT transformer SLD, Wiring Diagram Bus duct layout Cable routing & Sizing Cable Tray Routing & sizing Preparing Illumination layouts Reviewing the vendor Documents Inspection of Equipment & its Erection Having knowledge of C&I equipment & layout will be preferred Independent working as well as managing a team of design engineer and draftsmen Responsible for delivering designs with in BOQ quantities as well as within the quoted man hours

Review of manufacturer drawings for different equipment at substation level and submission to client & review of client comments and reply to the comments with revised vendor documents Ensure deliveries are aligned to Project Schedule Pre order offer reviews during tender and execution stage of the project Follow up with manufacturers for drawing submissions and incorporation of comments Checking of vendor GA parameters on primary equipment layout and coordinate same with vendor if any changes in layout design Providing support to Site team on site queries on manufactured equipment Submitting all engineering set of calculation and obtaining comments from review with client Releasing Manufact...

Summary Execute & analysis, design, test, or integration required to define and support systems that meet business standards and program / product requirements Prepare and present technical data to internal and external customers Document and communicate results of technical data generated Participate on teams assigned to address specific organizational initiatives Share engineering information and promote open dialogue Prepare invention disclosures to protect the technology that provides a competitive advantage to the business Assure proper documentation of technical data generated for the assigned projects and/or tasks consistent with engineering policies and procedures Job Description Des...

Experienced in designing skid-mounted modular packages (equipment layout, piping, structural framing, instrumentation & cable tray). Proficient in 3D CAD modeling, 2D drafting, detailing, BOM, and fabrication drawings using SolidWorks.

Post: Project (Sales) We are seeking a skilled AutoCAD Draughtsman to create commercial kitchen floor plans/commercial kitchen facility planning for our projects, detailed technical drawings of kitchen equipment for approvals. Provident fund Annual bonus Health insurance

skills : - Senior Electrical Engineer Location : - Navi Mumbai Prepare Basis of Design, Load list, Single Line Diagram, Schematics. Power distribution from 33kV / 22kV and downstream based on power ratings of equipment to various voltage levels 11kV / 6.6kV / 3.3kV & 415V. Other national standard voltage levels for GID project. Calculations for Transformer sizing. DG set sizing, UPS (Static / Rotary) and Battery Charger (DC UPS) sizing. Cable sizing calculation and Cable Schedule. Prepare Electrical Equipment Specifications and Data Sheets. Prepare Material Requisitions, TBE, Purchase Requisitions. Vendor Document review of Electrical and Mechanical Packages. Equipment Layout conforming to N...

Perform 3D modeling using AutoCAD Plant 3D for civil/structural, piping, and equipment(Inventor) Participate in 60%, and 90% 3D Model Reviews with stakeholders on EPC projects Knowledge of pipe stress analysis (CAESAR II or similar)

Performs complex BIM or Plant Data Centric assignments involving the use of multiple application platforms, such as Revit, Intergraph SmartPlant, Plant 3D, etc. software, to achieve set results and deadlines Duties and Responsibilities Works under limited supervision. Provides training and technical support to design staff on the Building Information Modeling system, which provides 3D models using project specifications and content. Direct project support and production to assigned projects and create the drawings as required using the standards and content to meet the job requirements (objects within the drawing, doors, lights, etc.). Develops and maintains HVAC system designs, including du...

About Us Tata Consulting Engineers Limited (TCE) is the largest Indian private sector engineering and project consultancy and an emerging global leader in integrated engineering solutions. With more than 60 years of engineering excellence, TCE has a presence in over 64 countries and over 12000 completed projects, the company operates in 3 core Industry segments -Infrastructure (Water, Environment, Urban Development, Buildings, Manufacturing Facilities, Ports and Harbours, Transportation), Power (Thermal, Hydro, Nuclear, Renewable, Transmission and Distribution) and Resources - Hydrocarbons and Chemicals (Oil, Gas and Refineries, Chemicals, Petrochemicals, Fertilizers, Speciality Chemicals, P...

Performs complex BIM or Plant Data Centric assignments involving the use of multiple application platforms, such as Revit, Intergraph SmartPlant, Plant 3D, etc. software, to achieve set results and deadlines. Duties and Responsibilities Works under general supervision to complete HVAC BIM design projects. Directs project support and production for assigned projects, creating drawings as required using standards and content to meet job requirements (objects within the drawing, doors, lights, etc.). Develops and maintains HVAC system models, including ductwork, piping, and equipment layouts. Coordinates with other disciplines (structural, electrical, plumbing) to ensure proper integration of H...

-Concept Engineering drawings (Process Flow Diagrams, Facility & Equipment Layouts/Sections/Elevations, Plot Plan) -Engineering drawings (Utility Generation & Distribution P&ID, Input info for detail eng.) -Revit modelling of Civil/Structure Drawings Required Candidate profile - Experience in development of Concept & Engineering for formulation facilities like Oral Solid/Liquid Dosages - Exp of 5-10 years (Pharma. consultancy / Design-Build-Contractor only) - cGMP norms

Review & prepare mechanical design basis MDS of equipment vendor evaluation, FAT & SAT Equipment Layout, piping GA Drawing, isometric drawing Piping MTO & BOQ for Green field & Brown Field Projects Project execution, Erection Commissioning

Job Sr Production Email punejob25@gmail.com contact -9356395439 Qualification: BE / DME Experience: 5 to 8 Years Location Aurangabad Salary: Based on skills and experience demonstrated during the interview, No bar for right candidate. Skills Required: HOT FORGING , QMS , IATF , ISO

Job Summary: Produces 3D Modeling, 2D layout, arrangement and fabrication drawings of the company s products and equipment assembled on skid and of the interconnecting facilities of the plant inside company scope Ensure that the drawings and documents output from the Plant 3D and P&ID Software comply with the Veolia standards and business requirements. Continuously improve outputs based on lessons learned and the state of the industry and the state of the art. Must be able to effectively communicate, organize and be efficient in time management with a team of engineers from multiple disciplines. High levels of decision making, organization and planning is required to be effective. Essential ...

Job Summary: Mechanical Engineer with 10+ years of experience in Pharma / ATF Industry. Expert level knowledge in Piping Engineering like Layout, Piping materials, specifications, Data sheets & 3D modeling tools (E3D.PDMS, Plant 3D, Revit & etc.) with Interdisciplinary coordination for all the Project phases. Responsibilities: Should have the ability to work as Discipline lead Lead and supervise Engineers / Designers / Modelers. Reviewing of Plot plan, Equipment layout, Piping layout, Isometrics and support details. Ensure and maintain the International Standards like ASME, ANSI, DIN, EN, ISO, BS etc., in piping design. Ensure that all design in compliance with local authorities code require...

Functions as a technical specialist or in a lead role. With minimal supervision, applies advanced engineering techniques and analyses. Continues building on knowledge to develop concepts and approach more complex engineering problems. May provide technical guidance over a group or supervise engineering staff on projects of low to medium complexity. May be responsible for developing, validating, and presenting specialist/technical output. Key Responsibilities Co-ordinate the overall Design Drafting group quality timely completion of their work within established man-hour budgets, taking care of technical organization problems. Assisting the Project leader in the preparation of execution strat...

Execute & analysis, design, test, or integration required to define and support systems that meet business standards and program / product requirements. Prepare and present technical data to internal and external customers. Document and communicate results of technical data generated. Participate on teams assigned to address specific organizational initiatives. Share engineering information and promote open dialogue. Prepare invention disclosures to protect the technology that provides a competitive advantage to the business. Assure proper documentation of technical data generated for the assigned projects and/or tasks consistent with engineering policies and procedures Job Description Desig...

Performs complex BIM or Plant Data Centric assignments involving the use of multiple application platforms, such as Revit, Intergraph SmartPlant, Plant 3D, etc. software, to achieve set results and deadlines Duties and Responsibilities Works under limited supervision. Provides training and technical support to design staff on the Building Information Modeling system, which provides 3D models using project specifications and content. Direct project support and production to assigned projects and create the drawings as required using the standards and content to meet the job requirements (objects within the drawing, doors, lights, etc.). Develops and maintains HVAC system designs, including du...

Job Description Summary General responsibilities:Execute & analysis, design, test, or integration required to define and support systems that meet business standards and program / product requirementsPrepare and present technical data to internal and external customersDocument and communicate results of technical data generatedParticipate on teams assigned to address specific organizational initiativesShare engineering information and promote open dialoguePrepare invention disclosures to protect the technology that provides a competitive advantage to the businessAssure proper documentation of technical data generated for the assigned projects and/or tasks consistent with engineering policies...

Performs complex BIM or Plant Data Centric assignments involving the use of multiple application platforms, such as Revit, Intergraph SmartPlant, Plant 3D, etc. software, to achieve set results and deadline. Works under limited supervision. Provides training and technical support to design staff on the Building Information Modeling system, which provides 3D models using project specifications and content. Direct project support and production to assigned projects and create the drawings as required using the standards and content to meet the job requirements (objects within the drawing, doors, lights, etc.). Qualifications Diploma / BE Electrical & Electronics with >3years experience post qu...

JD- Prepare & modify GA, assembly, fabrication, and layout drawings in AutoCAD (2D & 3D) Develop detailed component drawings from GA/concept drawings with accuracy Ensure compliance with design standards, tolerances & material specifications Post-3 Required Candidate profile ITI/ Diploma in Mechanical 2-3 Years of experience in Heavy Engineering / Steel Plant Equipment Drawings Knowledge of steel plant equipment (EAF, LRF, CCM & auxiliaries) Call:- Namrata- 8910291069

experience in Chemical/Process Plant Piping Engineering with strong knowledge of International Standards. Must be proficient in AutoCAD Plant 3D for 3D modeling of equipment, piping, civil/structural & preparation of all piping deliverables. Required Candidate profile experience in Plant 3D Spec Editor, creating intelligent P&IDs, isometrics, and piping support detailing. Knowledge of ASME, IBR, OISD, PMS standards; experience with PDMS/CADWorx

Job Title: Senior Engineer - Piping Location: Hyderabad Work mode: Work from office Job Summary: Mechanical Engineer with 12+ years of experience in Pharma / ATF Industry. Expert level knowledge in Piping Engineering like Layout, Piping materials, specifications, Data sheets & 3D modeling tools (E3D.PDMS, Plant 3D, Revit & etc.) with Interdisciplinary coordination for all the Project phases. Responsibilities: Should have the ability to work as Discipline lead. Lead and supervise Engineers / Designers / Modelers. Reviewing of Plot plan, Equipment layout, Piping layout, Isometrics and support details. Ensure and maintain the International Standards like ASME, ANSI, DIN, EN, ISO, BS etc., in pi...